Such is the scale of the Silverstone Festival, the amount to see, and the number of photos that I took over three days, that there are a total of four separate reports for the event. The first covers Car Club Displays, for marques from A – L, the second completes the Car Club Displays from M to Z, this is the third and the fourth and final report covers the Iconic Auctions event that took place.

CAR CLUB DISPLAYS

 

NOT JUST AT SILVERSTONE

Although some of the cars remain in position over the entire three days of the event, a lot of people who are attending on multiple days do move them, and so you can be pretty sure that if you pick a hotel somewhere near Silverstone – and we chose to stay at the Travelodge at the Bicester-Cherwell services by the M40 – then you are likely to see some nice cars in the car park, and so it proved with these which were parked up where we were staying.

RARE CARS DISPLAY

Featuring in the event once again after proving popular in 2021 and 2022 was a feature called the UK’s “Rarest Cars”. Sponsored by the Daily Telegraph, this was a collection of cars that were once common (in most cases) but which are now down to very small number of survivors. I really enjoyed this feature in the past and was looking forward to it again. Sadly, the numbers of cars were down significantly compared to 2022 and on the Friday very few of them were present at all It did get better on the Saturday and many of the cars were ones which had not been shown here in the pas though inevitably there were some repeats.

Audi 100LS: The premiere of the Audi 100 in 1968 was preceded by a turbulent history because its development was actually started in secret. In the mid-1960s, Volkswagen AG acquired Auto Union GmbH and prevented the company from developing any new models. This stipulation to only look after the existing models was ignored by Ludwig Kraus, then Technical Director at Auto Union GmbH. In 1965, Kraus wanted to expand the range of vehicles which the resuscitated Audi brand offered. He saw adding a model in the executive segment as the only way to keep an independent Auto Union GmbH afloat in a time when the Ingolstadt plant was being used for production of the VW Beetle. Without informing Volkswagen, Kraus developed and subsequently presented the concept before it was eventually given the go-ahead from the team in Wolfsburg. The Audi 100 debuted at the Frankfurt Show in 1968 in two-door and four-door sedan form. Rupert Neuer headed the design team, achieving a modern and aerodynamically efficient shape that managed to be visually lighter than the BMW and Mercedes-Benz competitors of the time while also distancing itself from the visual themes of its two rivals. The 100 had its own unique look, and the four rings were positioned prominently on the grille, signalling the re-emergence of the Audi marque. The 100 was initially powered by a longitudinally mounted, Daimler-based 1.7-litre four-cylinder, good for 115 hp and 119 lb-ft of torque, and was later joined by a 1.8-litre unit. Offered with a choice of a four-speed manual or a three-speed automatic transmission. “With the Audi 100, the Volkswagen Group suddenly added a car in its range that appealed to the up-and-coming Beetle buyers,” Audi says. “In addition, Audi managed to win many customers with the Audi 100 who identified themselves with other brands. The fact that from 1971, the large Audi could optionally be supplied with up to 112 hp also contributed to its success. Thanks to its lightweight construction, the Audi 100 GL was so appealing that customers increasingly switched from competing six-cylinder models to the new Audi.” Very quickly, the capacity of the Ingolstadt plant was pushed to its limits and thus Auto Union shifted the entire production of the Audi 100 to the Neckarsulm works in 1970. Volkswagen made an effort to push the model upmarket, in time setting its sights on offerings BMW and Mercedes-Benz, and the stylish Coupe was one manifestation of that ambition. It was not the only up-market car, of course, as there was still the NSU Ro80 as a stable mate, and there had been the ill-fated VW K70 but by 1976, however, it was clear which model had won out, and with nearly 800,000 produced, the Audi 100 pointed to a path forward for the entire Audi lineup, working to cement its place as Volkswagen’s upmarket division. From the first series alone, the company sold 800,000 units. There were four examples from the first generation here, a rare 2 door saloon and an even rarer 1969 Cabrio, the very stylish Coupe and a prototype electric car from 1976 which had a boot full of batteries.

Austin Ambassador: Many will tell you that this is the car that the Princess should always have been from launch, that is a hatchback. It is still not clear why Harris Mann’s boldly styled ADO71 car went into production with a small boot opening instead of the more useful large rear tailgate. By the time the Ambassador was launched in March 1982, the Princess had been on sale for 7 years, and so even a comprehensive facelift, which is what this change was – despite the fact that all the body panels apart from the front door skins were apparently new – could not really hope to compete against the recently launched all-new Vauxhall Cavalier or even Ford’ Sierra which would arrive later in the year. The Ambassador did have roominess on its side, with a lot of space for rear passengers, but it also had BL Build Quality, and some of the cars proved to be not particularly reliable. The 2.2 litre 6 cylinder E series engine was not offered, meaning that Ambassadors only came with the O Series engine, in 1700 and 2000cc guise. Top spec models, the HLS and Vanden Plas had a twin carburettor engine, but even these did not have a 5 speed gearbox, which was fast becoming a necessity for cars in this class. That coupled with the fact that the cars were not very inspiring to drive meant that despite the fact that the top spec cars were quite well equipped and nicely trimmed inside, the model’s appeal was limited. The Ambassador was only ever going to have a short life, as it was deleted once the Austin Montego hit the market in April 1984. Although engineered for left and right hand drive, only right hand drive models went into production, so the car was only sold in the UK. 43,427 were built in the two years which it was available, of which only a handful are still on the road, with a few more in SORN status.

Citroen BX Estate: Despite the fact that 2,315,739 BXs were built during its 12-year production run, and the car sold well in the UK, these are getting increasingly scarce, so it was nice to see a couple here, a very rare 4×4, which the owner, a real enthusiast for the model. has recently sourced, he told me and from the other end of the range, a 14E Leader. The rather angular hatchback was designed by Marcello Gandini of Bertone, based on his unused design for the British 1977 Reliant FW11 concept and his 1979 Volvo Tundra concept car. It was the second car to benefit from the merger of Peugeot and Citroën in 1976, the first being the Citroën Visa launched in 1978. The BX shared its platform with the more conventional 405 that appeared in 1987, except the rear suspension which is from a Peugeot 305 Break. Among the features that set the car apart from the competition was the traditional Citroën hydropneumatic self-levelling suspension, extensive use of plastic body panels (bonnet, tailgate, bumpers), and front and rear disc brakes. The BX dispensed with the air cooled, flat four engine which powered the GS, and replaced it with the new PSA group XY, TU and XU series of petrol engines in 1360 cc, 1580 cc and, from 1984, 1905 cc displacements. In some countries, a weaker, 80 PS version of the 1580cc engine was badged as the BX15E instead of BX16. A 1124 cc engine, in the 11TE, very unusual in a car of this size, was also available in countries where car tax was a direct function of engine capacity, such as Ireland, Italy, Portugal and Greece. The 11TE model was seen by foreign motoring press as slow and uncomfortable. It was fitted to the cars made from 1988 to 1993 and produced 55 hp. The 1.1 and 1.4 models used the PSA X engine (known widely as the “Douvrin” or “Suitcase Engine”), the product of an earlier Peugeot/Renault joint venture, and already fitted in the Peugeot 104 and Renault 14. The 1.6 version was the first car to use the all-new short-stroke XU-series engine. It was produced in a new engine plant at Trémery built specifically for this purpose, and was later introduced in a larger 1.9-litre version and saw long service in a variety of Peugeots and Citroëns. The XUD diesel engine version was launched in November 1983. The diesel and turbo diesel models were to become the most successful variants, they were especially popular as estates and became the best selling diesel car in Britain in the late 1980s. Despite being launched on the continent in the autumn of 1982, it wasn’t launched onto the British market until August 1983, initially only with 1.4 and 1.6 petrol engines, although further engine options and the estate model would arrive later, and it would go onto become one of the most popular foreign-built cars here during the second half of the 1980s. A year after the launch of the hatchback model, an estate version was made available. In 1984 power steering became optional, welcome particularly in the diesel models. In the late 1980s, a four-wheel drive system and turbodiesel engines were introduced. In 1986 the MK2 BX was launched. The interior and dashboard was redesigned to be more conventional-looking than the original, which used Citroën’s idiosyncratic “satellite” switchgear, and “bathroom scale” speedometer. These were replaced with more conventional stalks for light and wipers and analogue instruments. The earlier GT (and Sport) models already had a “normal” speedometer and tachometer. The exterior was also slightly updated, with new more rounded bumpers, flared wheelarches to accept wider tyres, new and improved mirrors and the front indicators replaced with larger clear ones which fitted flush with the headlights. The elderly Douvrin engine was replaced by the newer TU-series engine on the 1.4 litre models, although it continued to be installed in the tiny BX11 until 1992. 1988 saw the launch of the BX Turbo Diesel, which was praised by the motoring press. The BX diesel was already a strong seller, but the Turbo model brought new levels of refinement and performance to the diesel market, which brought an end to the common notion that diesel cars were slow and noisy. Diesel Car magazine said of the BX “We can think of no other car currently on sale in the UK that comes anywhere near approaching the BX Turbo’s combination of performance, accommodation and economy”. In 1989, the BX range had further minor revisions and specification improvements made to it, including smoked rear lamp units, new wheeltrims and interior fabrics. Winning many Towcar of the Year awards, the BX was renowned as a tow car (as was its larger sister, the CX), especially the diesel models, due to their power and economy combined with the self levelling suspension. The biggest problem of the BX was its variable build quality, compared to its competition. In 1983, one quarter of the production needed “touchups” before they could be shipped, though later models were more solid. The last BX was sold around 1994, by which time its successors had already been launched. It had been partially replaced by the smaller ZX in early 1991, but its key replacement was the slightly larger Xantia that went on sale at the beginning of 1993. The BX was launched onto the right-hand drive UK market in August 1983, initially only with 1.4 and 1.6 petrol engines, although by 1986 it had been joined by more engine options as well as a five-door estate model. The BX enjoyed a four-year run as the UK’s best selling diesel engine car from 1987, and was consistently among the most popular imported cars.

Fiat Uno: Fiat launched the Uno, the Tipo 146,  in January 1983, just one day before the equally iconic Peugeot 205, to replace the elderly Fiat 127. Both were huge sellers, and deservedly so too, but it was the Fiat that sold in greater quantity, with over 8 million examples produced. It was Italy’s best selling car, and by some margin, throughout its 10 year production life, though you might find that hard to believe now, as they were are not a common sight even in Italy. The 127 had revolutionised the supermini market on its launch more than 10 years earlier, and the Uno followed the same format, but brought uptodate. Designed by Giorgetto Giugiaro’s ItalDesign company, its tall, square body utilising a Kamm tail achieved a low drag coefficient of 0.34 won it much praise for interior space and fuel economy as well as its excellent ride and handling, and was widely regarded as the most innovative small car in Europe at the time of its launch. It incorporated many packaging lessons learnt from Giugiaro’s 1978 Lancia Megagamma concept car (the first modern people carrier / MPV / mini-van) but miniaturised. Its tall car / high seating packaging is imitated by every small car today. It reversed the trend for lower and lower built cars. It showed that not just low sleek cars could be aerodynamic, but small, roomy, boxy well packaged cars could be too. There was a lot of activity in the supermini class in 1983, as the Uno hit the UK market a couple of months before the Peugeot 205 – another small European car which became the benchmark for this market sector, enjoying a long production life and strong sales, and just after General Motors launched its new Opel Corsa/Vauxhall Nova. Within a few months of its launch it had gained two new major competitors in the shape of the restyled Ford Fiesta and Nissan’s new Micra. UK sales began in June 1983, and more than 20,000 were sold in its first full year and peaking at more than 40,000 sales in 1988, making it one of the UK’s most popular imported cars during the 1980s. In December 1983, it was European Car of the Year for 1984, finishing narrowly ahead of the Peugeot 205. Initially, the Uno was offered with the 0.9 litre (903 cc) 100-series OHV, 1.1 litre (1116 cc) and 1.3 litre (1301 cc) 128-series SOHC petrol engines and transmissions carried over from the 127. The Uno’s badging was not by the commonly used measurement of engine size but by metric horsepower: 45, 55, 60, 70, or 75. The Uno was available as either a three- or five-door hatchback. It also featured ergonomic “pod” switchgear clusters each side of the main instrument binnacle, (that could be operated without removing the driver’s hands from the steering wheel), although indicators remained on a stalk; an unusual arrangement similar to that used by Citroën. The Uno had MacPherson strut independent front suspension and twist-beam rear suspension with telescopic dampers and coil springs. From 1985, the 1.0 litre (999 cc) SOHC Fully Integrated Robotised Engine (FIRE) powerplant was offered, replacing the 0.9 litre unit. This was a lighter engine, built with fewer parts, and gave improved performance and economy. The most luxurious version, the single-point injected 75 SX i.e., had remote door locks, integrated front foglamps, and the oval exhaust tip also used on the Turbo. In April 1985 the hot hatch version of the first series Uno – the Uno Turbo i.e. – was launched as a three-door only derivative. It competed with the likes of the Ford Fiesta XR2, MG Metro Turbo and Peugeot 205 GTI. The Uno was replaced by the Punto in late 1993, although production for some markets continued for some time after that.

Ford Consul: From inception, Ford in the UK and Ford in Germany produced their own ranges of cars, and in markets where both were sold, they competed against each other. It was only with the Consul and Granada that were launched in the spring of 1972 that they finally arrived at a single model range that would be offered to customers. But even then, there were differences between the UK-market Dagenham built and European market Cologne built cars, with the British Pinto 2 litre and Essex 3 litre V6 engines under the bonnet of UK market cars and the 1.7 and 2 litre V4 engines that had been used in the high end Taunus models continuing in the continental cars. A two door model that was added to the range in March 1973 was never offered to British customers, but was developed as there was still a significant market for large saloons with just two doors in Germany (the Mark 2 Granada was offered with 2 doors as well), and there was a Coupe. This one did eventually come to the UK, in 1974, when it was launched as the top of the range 3.0 Ghia model, with just about every conceivable item of equipment included as standard, and the first Ford to bear the Ghia badging that would be systematically applied to every range in the next couple of years. A Saloon version with Ghia badging followed later in the year, and this sold more strongly, so the Ghia Coupe was never a big seller, and is quite rare now.

Ford Cortina 80 Estate: Final representative of the Cortina range was this Cortina 80, sometimes known as the Mark V. It was announced on 24 August 1979. Officially the programme was code named Teresa, although externally it was marketed as “Cortina 80”, but the Mark V tag was given to it immediately on release by the press, insiders and the general public. Largely an update to the Mark IV, it was really a step between a facelift and a rebody. The Mark V differentiated itself from the Mark IV by having revised headlights with larger turn indicators incorporated (which were now visible on the side too), a wider slatted grille said to be more aerodynamically efficient, a flattened roof, larger glass area, slimmer C-pillars with revised vent covers, larger slatted tail lights (on saloon models) and upgraded trim. Improvements were also made to the engine range, with slight improvements to both fuel economy and power output compared to the Mark IV. The 2.3 litre V6 engine was given electronic ignition and a slight boost in power output to 116 bhp, compared to the 108 bhp of the Mark IV. Ford also claimed improved corrosion protection on Mark V models; as a result, more Mark Vs have survived; however, corrosion was still quite a problem. The estate models combined the Mark IV’s bodyshell (which was initially from the 1970 Ford Taunus) with Mark V front body pressings. A pick-up (“bakkie”) version was also built in South Africa. These later received a longer bed and were then marketed as the P100. Variants included the Base, L, GL, and Ghia (all available in saloon and estate forms), together with Base and L spec 2-door sedan versions (this bodystyle was available up to Ghia V6 level on overseas markets). The replacement for the previous Mark IV S models was an S pack of optional extras which was available as an upgrade on most Mark V models from L trim level upwards. For the final model year of 1982 this consisted of front and rear bumper overriders, sports driving lamps, an S badge on the boot, tachometer, 4 spoke steering wheel, revised suspension settings, front gas shock absorbers,’Sports’ gear lever knob, sports road wheels, 185/70 SR x 13 tyres and Fishnet Recaro sports seats (optional). Various “special editions” were announced, including the Calypso and Carousel. The final production model was the Crusader special edition which was available as a 1.3 litre, 1.6 litre, and 2.0 litre saloons or 1.6 litre and 2.0 litre estates. The Crusader was a final run-out model in 1982, along with the newly introduced Sierra. It was the best-specified Cortina produced to date and 30,000 were sold, which also made it Ford’s best-selling special edition model. Another special edition model was the Cortina Huntsman, of which 150 were produced. By this time, the Cortina was starting to feel the competition from a rejuvenated Vauxhall, which with the 1981 release Cavalier J-Car, was starting to make inroads on the Cortina’s traditional fleet market, largely helped by the front wheel drive benefits of weight. Up to and including 1981, the Cortina was the best selling car in Britain. Even during its final production year, 1982, the Cortina was Britain’s second best selling car and most popular large family car. On the continent, the Taunus version was competing with more modern and practical designs like the Talbot Alpine, Volkswagen Passat, and Opel Ascona. The very last Cortina – a silver Crusader – rolled off the Dagenham production line on 22 July 1982 on the launch of the Sierra, though there were still a few leaving the forecourt as late as 1987, with one final unregistered Cortina GL leaving a Derbyshire dealership in 2005. The last Cortina built remains in the Ford Heritage Centre in Dagenham, Essex, not far from the factory where it was assembled.

Ford Sierra: By 1978, Ford Europe was working on a new mid-range model to replace the Cortina/Taunus during the early 1980s, working under the codename “Project Toni”. Ford had confirmed during 1981, a year before the Sierra’s official launch, that its new mid-range car would carry the Sierra name, signalling the end of the Taunus and Cortina nameplates after 43 years and nine generations respectively 20 years and five generations. In September that year, it had unveiled the Probe III concept car at the Frankfurt Motor Show, hinting at what the new car would look like when the final product was unveiled 12 months later. At first, many found the design blob-like and difficult to accept after being used to the sharp-edged, straight-line three-box styling of the Taunus/Cortina, and it was nicknamed “the jellymould”. The shape served a purpose though, producing a drag coefficient of 0.34, a significant improvement over the boxy outgoing Taunus’s/Cortina’s 0.45. This aerodynamic design was key for reducing fuel consumption according to Ford, and was even used as compensation for the V6-engines. The interior was more conventional, although Ford took a page from BMW by angling the center of the dashboard towards the driver. Sales were slow in the first months – the situation being exacerbated by heavy discounting by Ford dealers of surplus Cortina stock from the autumn of 1982 onwards, with more than 11,000 new Cortinas being registered in 1983. However in 1983, its first full year of sales, the Sierra managed nearly 160,000 sales in Britain, outsold only by the smaller Escort. Ford had also launched the more conservatively designed Escort-based Orion saloon that year, which found favour with buyers who would otherwise have been the Sierra’s target customers. In West Germany, it was proving very popular from an early stage; within months of its launch, it was reportedly achieving treble the number of sales that the Taunus had been attaining – though in West Germany, the Taunus had not been quite as popular or iconic as its Cortina equivalent had been in Britain. It was later in the Sierra’s life that the styling began to pay off; ten years after its introduction, the Sierra’s styling was not nearly as outdated as its contemporaries, even though all major competitors were newer designs, though the Sierra had been tweaked on several occasions and many new engines had been added. The most notable changes came at the autumn of 1987, with a major facelift and the addition of a 4-door saloon (UK: Sapphire). As other manufacturers adopted similar aerodynamic styling, the Sierra looked more normal. At its peak, it was Britain’s second best selling car in 1983, 1988 and 1989, and was still Britain’s fifth best selling car in 1992. Its best year was 1989, when more than 175,000 were sold. However, it was outsold by the Vauxhall Cavalier in MK2 form during 1984 and 1985, and then from 1990 until its demise by the MK3 Cavalier. Nevertheless, it comfortably outsold its second key rival, the Austin Montego, which was launched in April 1984. Between 1985 and 1988, the Sierra faced fresh competition in Europe from the likes of the Renault 21 and Peugeot 405, while Japanese carmaker Nissan was producing its Bluebird model in Britain from 1986. Early versions suffered from crosswind stability problems, which were addressed in 1985 with the addition of “strakes” (small spoilers) on the rear edge of the rubber seals of the rear-most side windows. These shortcomings saw a lot of press attention, and contributed to early slow sales, when it was outsold by its key rival the Vauxhall Cavalier in 1984 and 1985. Other rumours that the car hid major crash damage (in part true, as the new bumper design sprung back after minor impact and couldn’t be “read” to interpret major damage) also harmed the car’s reputation. This reached near-hysterical heights in its early months on sale, with UK press making a report that Ford would reintroduce the previous Cortina model out of desperation. These reports were swiftly denied by Ford. However, sales began to rise during 1983, and it finished as Britain’s second best selling car behind the Escort. After being outsold by the Cavalier for the next two years, it regained its lead of the market sector in Britain during 1986, and a refreshed range (with more engine options as well as the introduction of a saloon) enjoyed a surge in sales from 1987, though the MK3 Cavalier finally outsold it in 1990. Even in 1992, the Sierra was still Britain’s fifth best selling car. It was nicknamed “the salesman’s spaceship” on account of its status as a popular fleet car in Britain. In contrast to the Sierra’s groundbreaking exterior design, the drivetrain was quite outdated as it was adopted from the outgoing Taunus/Cortina. Engines and gearbox wear upgraded, but the Sierra maintained the rear-wheel drive configuration. Most competitors were already switched to front-wheel drive around that time. Ford claimed however this set-up was required to offer V6-engines, which had to contribute to the Sierra’s driving comfort. New for the Sierra was a diesel engine, although the engine itself wasn’t new at all. Similar to the Ford Granada, Ford used an “Indenor”-engine which was designed by Peugeot in the 1950s. While the Granada was offered with 1.9, 2.1 and 2.5 diesels, the Sierra unit had a displacement of 2,3 litre. This engine was replaced only in 1989 by an all-new 1.8 liter turbodiesel, developed by Ford itself. The Sierra had a four-speed manual gearbox as standard, with a five-speed as option but standard on the 2.3D and 2.3 V6. At a time when the rival Vauxhall Cavalier was offered with a five-speed, this led to some critics commenting that the Sierra was somewhat underpowered. In the mid-1980s, many smaller cars (some even two segments smaller) featured five-speed gearboxes as standard. One of the most striking design features of the Sierra was its closed front panel instead of a grille, which was later also to be found on the 1985 Ford Taurus. The air intake was situated below the front bumper, making the Sierra a so-called ‘bottom breather’. The headlights were integrated in this front panel while the indicators were mounted in the bumper within a combined unit with the foglights. However, this set-up was only present on the top-of-the-line “Ghia”-trim as well on the later introduced XR4i sportmodel. The other Sierra models had a more traditional front end with a two-bar grille between the headlights, being unpainted on the base model. These models had the indicators in the bumper as well, although being slimmer but wider and without the foglights. Both the Ghia and XR4i had wide headlights with two lenses while the other models had smaller lights with a single lens. For the 1985 model year, all the lower-spec models, except the base model, adopted the Ghia and XR4i’s front grille and headlight treatment. However, the second lens of the lower-spec models had no actual light within it. On the Ghia and XR4i this lens contained additional high beam lamps. The South-African XR8 model’s front end was similar to the XR4i’s but featured a small grille between the headlights. The rear lights of the Ghia, as well as the very early XR4i’s, were the same shape and layout as other models, but featured tiny horizontal black strakes on the lenses to give the impression that they were smoked. The car was replaced by the Mondeo in Europe in April 1993, though stocks lasted for about two years afterwards. The Sierra remained a popular second-hand buy and common sight on British roads until well beyond the year 2000.

Hillman Hunter GLS: The Hunter is perhaps the best known of this range of cars that Rootes Group produced under several badge-engineered marques from 1966 to 1979. It is amongst the last Rootes designs, developed with no influence from future owner Chrysler. A substantial number of separate marque and model names applied to this single car platform. Some were given different model names to justify trim differences (Hillman GT, Hillman Estate Car) and to make things more complicated, from time to time all models were sold in some European markets under the Sunbeam marque (Sunbeam Sceptre for instance), and at other times used UK marque/model names. To add complication, Singer Gazelle/Vogue models were also sold in the UK for one season badged as Sunbeams after the Singer brand was withdrawn. The Arrow range was conceived in 1962. Following the Hillman Imp, consideration was given to developing a larger rear-engined car, but this concept was dismissed, and the engineering settled on for the new car was more conventional and closer to the layout of the existing Audax series (which included the previous Hillman Minx). With cash-strapped Rootes struggling amid continuing engine cooling problems with the Imp, which often resulted in warped cylinder heads, the cautious Arrow broke little new engineering ground. New parts were largely based on tried and tested Rootes components, using a new but strong 5-bearing version of the well-proven 1725 cc overhead valve petrol engine as a starting point which varied in output from 66 bhp to 88 bhp. The engine was inclined by a modest 15 degrees, to allow for a lower bonnet line and to enable packaging of the carburettors. This engine was further uprated by specialists Holbay, employing two Weber 40DCOE carburettors to produce 107 bhp for the Sunbeam Rapier H120 and Hillman Hunter GLS. A smaller 1500 cc engine was the standard for manual versions of the Hillman Minx and the Singer Gazelle, and the Hillman Hunter DeLuxe model which succeeded the Minx. Automatic models were all powered by the 1725 cc engine. Particular attention was paid to weight and cost to bring the vehicle in line with its natural competitors, including the Mark 2 Ford Cortina. For the first time in a Rootes car MacPherson strut suspension featured at the front, with a conventional live axle mounted on leaf springs at the rear. Other firsts for Rootes in the new car were curved side glass and flow-through ventilation. Manual transmissions were available in four-speed form with an optional Laycock de Normanville overdrive, or Borg-Warner automatic transmission, again as an option. Initially, the Borg Warner Type 35 3-speed automatic was offered, then the Type 45 four-speed automatic became available in 1973. The handbrake was situated between the driver’s seat and door rather than between the front seats. This followed the practice in the ‘Audax’ cars. The first Arrow model to be launched, the Hillman Hunter, was presented as a replacement for the Hillman Super Minx. The Hunter was lighter than its predecessor and the wheel-base of the new car was actually 2½ inches shorter than that of the old, but the length of the passenger cabin was nonetheless increased by moving the engine and the toe-board forwards. For the first two years there were few changes. However, in May 1968 power assisted brakes were made available as a factory fitted option. Hitherto this possibility had been offered only as a kit for retro-fitting: it was stated that the factory fitted servo-assistance, at a domestic market price slightly below £13, would be cheaper for customers. A mild facelift in 1970 gave new grilles to the various Hunter trim levels, and some derivatives gained a (then) more fashionable dashboard, exchanging wood for plastic, but the car remained fundamentally the same throughout its life. A more detailed facelift for 1972 brought a new all-plastic dashboard with deeply hooded round dials (earlier versions had either a strip speedometer or round dials in a flat dashboard for more expensive models like the Vogue), new steering wheel, plastic instead of metal air cleaner, reshaped squarer headlamps in a new grille and some engine tuning changes. For 1975, bumpers were enlarged and the tail lights were enclosed in a full-width anodised aluminium trim piece. Following the 1967 acquisition of Rootes by Chrysler, the Arrow derivatives were rationalised until only the Hillman Hunter version was left by 1976. From September 1977 it was re-badged as a Chrysler, which it was to be for the remaining 2 years of its life. Hunter production was switched in 1969 to Rootes’ troubled Imp plant in Linwood, from its original home of Ryton. Sales were lower after 1975 following the launch of the Chrysler Alpine, a similar sized car but with front-wheel drive and a hatchback bodystyle, at a time when rear-wheel drive saloons still dominated in this sector. Following the Hillman Avenger’s move to Linwood in 1976, the very last European Hunters were assembled in the Santry plant, Shanowen Road, Ireland from “complete knock down” (CKD) kits until production ended in 1979 – but no evidence exists to suggest that the Talbot badge was applied to any production Hunter following Chrysler Europe’s 1978 takeover by Peugeot, and the application of that badge to other Chrysler models sold on or after 1 August 1979. The final Chrysler Hunter was built in September 1979 in Porirua, New Zealand, and was donated to the Southward Museum. In 2000 the Museum sold the car to a private collector.

Honda Accord: Debuted on 22 September 1981, in Japan, Europe, and North America, this second generation of the Accord being produced in Japan, also became the first to be built in the United States, at Honda’s plant in Marysville, Ohio. Since its first year in the American market, it also became the best-selling Japanese nameplate in the United States, retaining that position for about 15 years. In Japan, a sister model called the Honda Vigor was launched simultaneously with the new Accord. This allowed Honda to sell the product at different sales channels called Honda Clio, which sold the Accord, and Honda Verno, that sold the Vigor. Modernizing the interior and exterior, the second-generation Accord was mechanically very similar to the original, using the same 1,751 cc EK-1 CVCC engine in the Japanese market. Vehicles with a manual transmission and the CVCC carburetor earned 13.6 km/L (38 mpg‑imp; 32 mpg‑US) based on Japanese Government emissions tests using 10 different modes of scenario standards, and 108 bhp, and 23 km/L (65 mpg‑imp; 54 mpg‑US) with consistently maintained speeds at 60 km/h. European market cars received the tested 1.6-litre EL1 engine with 79 bhp DIN at 5000 rpm. This car included popular features of the time such as shag carpet, velour cabin trim, and chrome accents. An optional extra on the 1981 Accord was an Electro Gyrocator, the world’s first automatic in-car navigation system. Japanese market cars were available in Silver, Sky Blue, and Beige. The LX hatchback offered a digital clock and slightly higher fuel economy (due to its lighter weight). In Europe, the Accord was available as a fairly well equipped (for the time) standard version, as well as a very luxurious EX model at a modest upcharge. In the United States, Federal lighting regulations required headlamps of sealed beam construction and standard size and shape on all vehicles, so Accords in North America were equipped with four rectangular headlamp units rather than the aerodynamic composite replaceable-bulb units used on Accords sold outside North America (note European specification imagery). Other Automotive lighting variations included amber front and red rear side marker lights and reflectors in North America, and headlamp washers and a red rear fog lamp for European markets. Japanese-market Accords were unique from all other markets in that they offered adjustable ride height control and side-view mirrors installed on the mid-forward wings. In November 1982, Honda made a fully four-speed automatic available with the 1.8-litre engine, a major improvement over the earlier, three-speed semi-automatic “Hondamatic” transmission. This quickly filtered through to export markets, where the outdated Hondamatic was soon superseded entirely. The manual five-speed transmission remained unchanged. A new 120 mph speedometer replaced the earlier 88 mph unit. The Special Edition (SE) featured Novillo leather seating, power windows, a power sunroof, and door locks. Gray was added as a colour option. A slightly modified EK-2 engine was introduced, replacing the earlier EK-1, albeit still carbureted. A new model arrived in late 1985.

Lancia Trevi: Final member of the Beta family to appear was the Trevi, or Beta Trevi as it was called until 1982, which was introduced in 1980. The chief engineer for the Beta was Sergio Camuffo who was also responsible for the original Beta and the Gamma and numerous other models. The Beta, which was fitted with the same interior as the Trevi, was sold for two years alongside the Trevi (and sold as the Beta Berlina) Sales literature from Lancia emphasised that the car was both luxurious and sporting in nature. Lancia’s intention was that the restyled Beta would to help re-establish Lancia’s credibility after the debacle of the rusting Betas: “Lancia´s position took an unreasonably big knock as a result of the revelation that they were buying back cars with corroded sub-frame mounting points…a new Lancia today – thanks to the over-compensation that was necessary to make their point – promises to be as rust resistant as any of its rivals” wrote UK’s Autocar in 1981. The review continued to say the Trevi was “a conventional three-box saloon…it is a Beta under its skin but most the body panels and the interior are completely new.” The sales literature explained that the designers set out to create a classic three-box notchback saloon. The appearance of the car drew this comment from Autocar: “The Trevi is, to most eyes, a rather curious looking car, an odd combination of curves and angles, that produces an incipient spoiler from the slight upturn at the rear of the roof panel”. The introduction of a saloon body-style was part of a general conservative trend in which existing fastback cars or unusually-styled cars were given more conventional appearances. The VW Golf body was given a boot in 1979 to become the VW Jetta, the Citroën Visa gained a grill as did the Fiat Ritmo, and the fastback Simca 1307 was restyled with a boot and sold as a Solara, and the Saab 900 was sold in booted form as the 900 CD “The residents of Staid Lane” wrote Tumminelli, “preferred conformity…as a courtesy to Reagan, Thatcher and Kohl, the old-fashioned saloon, standard bearer of the bourgeouisie, must be reanimated”. The Trevi was available initially with two engines, a 1600 and 2000, both fitted with Weber or Solex carburetors. In the UK automatic transmission was optional only on the larger engined cars. In 1981 Bosch electronic ignition was made available on the 2000IE models. This allowed the engine to produce 122 bhp at 6,400 rpm (compared to 115 bhp at 5,500 rpm). The Trevi Volumex was the last version of the car, introduced in 1982 at the Turin motor show and designed to improve performance without affecting fuel economy. Fitted with a twin scroll Roots-type supercharger (and carburettors, rather than the expected fuel injection), this increased output to 135 PS. This development meant the Trevi was the first car fitted with a mechanically-driven supercharger in nearly five decades. It had revised front seats, a matt-black chin spoiler and plusher trim, with the seats upholstered in Zegna materials. As for the 2000IE, the Volumex also received a much-praised power steering from ZF as standard. Lancia UK did not import this version of the car to Great Britain and Northern Ireland. Production of the Trevi was discontinued in 1984. In total 36,784 examples of the Trevi were produced. There are fewer than 10 of them, in the UK now.

Mitsubishi Lancer 2000 Turbo: In 1979, the all new Lancer EX was unveiled in Japan. Its new, clean and aerodynamic styling with integrated plastic bumpers reflected that of the recently introduced Galant and Sapporo. It was of a more European appearance than earlier Mitsubishi vehicles. This generation is only available as 4-door sedan, the 2-door sedan was axed while the previous generation Celeste coupé and wagon/van were continued for a few more years. Considerably more spacious, it grew in all dimensions. Only two engines were offered at first, a 1.4-litre MCA-Jet equipped engine paired with Mitsubishi’s Silent Shaft Technology, which generated 80 PS (79 hp) and a 1.6-litre engine that generated 85 PS (84 hp). The MCA-Jet system was an entirely new concept when compared with the previously used carburettor system. The MCA stands for Mitsubishi Clean Air which meant that the EX passed both Japan and US emission standards, while the new cylinder head design of the engine gave way for a Jet valve which introduced an extra swirl of air to the combustion chamber, swirling the fuel-air mixture for a cleaner, efficient and more thorough burn. In addition to these improvements, another breakthrough in the Lancer lineup was the Silent Shaft Technology, which was actually two counterbalancing shafts that rotated in opposite directions, cancelling the power pulses inherent in an inline four-cylinder engine. This reduced both engine noise and vibration, and provided a smoother driving experience. The 1.8-litre Sirius 80 engines were then introduced in the Lancer in 1980, expanding the Lancer’s range of engines. Also, a turbocharged, 135 PS (133 hp) engine was added in 1980 for sportier performance, and an intercooler system was also integrated in the existing turbocharged engine to produce 160 PS (158 hp) in 1983. In 1980, The Lancer EX was introduced with a 1.8-litre turbocharged inline-four option known as the 1800GSR and GT Turbo. The first generation 1800GSR and GT were only available with a turbocharged, non-intercooled 135 PS. In Europe, the Lancer EX sold well as its restrained styling better matched the desires of European buyers than its somewhat fussy predecessor. Other considerations concerned handling and also the demand for more passenger room, as Mitsubishi tailored the Lancer towards European consumers. It went on sale locally after making its European premier at the 1979 Frankfurt Show. Unlike in Japan at the time of introduction, European buyers could get a 1.2-litre option which suited local tax conditions. This engine later did become available in Japan as well, beginning in May 1981, but was discontinued in 1983 after the introduction of the smaller Lancer Fiore. Claimed outputs in Europe were lower than in the domestic market because of the net rating, with the 1200, 1400, and 1600 being good for 54, 67, and 80 bhp respectively. Here, the Lancer EX was also offered with a turbocharged 2.0-litre SOHC engine, known as the Lancer EX2000 Turbo. It achieved a maximum output of 170 PS (168 hp) and managed a top speed of 200 km/h (124 mph). This model was equipped with Electronically Controlled Injection (ECI). A rally version of the Lancer 2000 Turbo was made and homologated for Group 4 and Group B, made out 280 PS (276 bhp). At home, sales of the turbo model were low because of emission regulations Japan imposed at that time.

Morris Ital: The Ital was given the design code ADO73 F/L (as internally it was considered a facelift of the Series 2 Marina (ADO73) launched in 1976) and was first launched on 1 July 1980. It took its name from Giorgetto Giugiaro’s Italdesign studio, who had been employed by BL to manage the reengineering of the Morris Marina, a car which had been produced by the company since 1971. BL’s advertising emphasised the car’s connection with the Italian design house, which had not had a direct role in the styling of the new car, which had been handled in-house by Harris Mann. Italdesign had been involved in a consultancy role to help design new tooling and assembly methods and work out how to integrate the altered parts of the new car into the existing Marina production chain. This is why, despite bearing the studio’s name, the Ital is absent from lists of the styling jobs handled by the firm. It was originally planned to brand the car as the Morris Marina Ital, but for most markets the Marina name was dropped on the orders of Michael Edwardes and only the Ital name was used. The Ital had revised exterior styling, but retained the Marina’s 1.3 and 1.7 litre petrol engines and rear-wheel drive chassis. The dashboard and interior of the Marina were also carried over largely unaltered, including the main fascia panel which faced ‘away’ from the driver. The Marina’s coupé variant was not produced in Ital form, but the four door saloon, five door estate and pick up and van versions were carried over from the Marina range. From October 1980, an automatic version of the Ital was available with the 2.0 litre O-Series power unit, as the range topping 2.0HLS. Only about 1,000 2.0HLS models were sold so due to this and their short production run, the 2.0HLS is now the rarest Ital model. In November 1981 all HL and HLS models were fitted with upgraded interior trim. Finally, in September 1982, a revised Ital range was introduced. The L and 2.0 litre models were dropped and the HL and HLS were replaced by the SL and SLX models. Front suspension was changed to telescopic front dampers across the range and parabolic rear springs were also fitted, together with additional soundproofing and improved trim. Thus cropped, the range now consisted of the 1.3 SL and SLX saloon, 1.3 SL estate, 1.7 SLX saloon, and the 1.7 SL saloon and estate. The saloon models were dropped in February 1984, with the estate models remaining in production until the summer of that year.

Nissan Prairie: The Nissan Prairie (is an automobile manufactured and marketed by Nissan from 1981 to 2004. Considered a mini MPV or a compact MPV. It was also marketed as the Multi in Canada and the Stanza Wagon in the United States. In Japan, it was exclusive to Nissan Bluebird Store locations, then later at Nissan Blue Stage sales channels. The Prairie had a very flexible seating capability and sliding rear doors on both sides of the vehicle, with a liftgate in the back. The name “prairie” was derived from French which means an extensive area of relatively flat grassland, similar to “steppe” or “savanna”. The Nissan Prairie, known in Canada as the Multi and the United States as the Stanza Wagon, was equipped with a four-cylinder engine, with either a manual or automatic transmission. Available with front wheel drive or optional four wheel drive, the vehicle had rear passenger sliding doors on both sides of the vehicle, and a folding rear seat, designed to increase the carrying capacity of the passenger compartment. The rear tailgate opened upwards as one complete unit, in a similar fashion to a hatchback or station wagon. The Prairie competed with the Toyota Sprinter Carib with a similar wagon approach, Mitsubishi Chariot, and the Honda Shuttle. The Prairie resembled a tall station wagon / estate with the addition of sliding side doors. It was available with five seats, though seven and eight were also available in some markets. It was developed from the Nissan Sunny platform, while using the powertrain from the Nissan Stanza. It was a companion model to the more traditional cabover Nissan Vanette, offering buyers a choice of appearance and flexibility. The trailing arm torsion beam rear suspension was borrowed from the Pulsar Van (VN10; sold as the Cherry Wagon in Europe). Some reviewers commented that when driven hard, undesirable body characteristics were exhibited, possibly due to the combination of missing B-pillar and torsion beam rear suspension. Strong understeering characteristics were also typical. The Prairie design was strongly inspired by the Lancia Megagamma concept by Giorgetto Giugiaro and ItalDesign, shown in 1979, and offered Japanese buyers a spacious, flexible passenger/cargo arrangement that complied with Japanese Government dimension regulations and used small displacement engines that offered Japanese buyers options with regards to annual road tax obligations. The first generation Prairies were innovative vehicles – featuring no B-pillar between the front and rear doors (instead the interlocking front and sliding rear doors locked onto both the floor and roof of the vehicle); front seatbelts mounted on the doors (excluding the US versions) that facilitated a totally unimpeded side entrance; front seats that could be slid all the way to the front of the passenger compartment and fully reclined; rear seats that could not only be folded away conventionally, but could also be reclined fully to make a double bed (in combination with the front seats); rear window winders that folded into themselves (to prevent catching when the doors were slid open); tailgate that opened past the floor of the very low and flat luggage compartment (the centre section of the rear bumper was mounted on the tailgate); optional front-facing third row of seats. This type of entry was later introduced on the Toyota Isis, but only on the passenger side. It was originally launched in Japan with a 1.5- or 1.8-litre Inline-four engine mated to a five-speed gearbox. Another notable addition to the Japanese market’s models was an optional column shifted manual. A four-wheel drive version followed later in the car’s life. An extensive accessories and options list was available in the Japanese Domestic Market, including a kit that effectively turned the vehicle into a campervan. In January 1985 a facelifted version was introduced, with slightly modified engines. These later cars received a new grille treatment and an entirely redesigned rear end: the bumper was now mounted separately to provide more stability after earlier versions had come under criticism for being much too flexible. This redesign also included taller, flush-fit rear side windows. In September 1985 the 4WD model finally appeared, using a larger 2-litre engine and the rear axle from the Nissan Sunny 4WD (B12). A 4WD model had been planned from the beginning,but the original bodyshell’s lack of rigidity made Nissan rethink the concept. The vehicle was launched as the Datsun Prairie in Europe and was rebranded to Nissan along with the rest of the range from 1984, at first featuring “Datsun by Nissan” badging and then solely “Nissan” badging from 1985. However, as Prairie was a slow but steady seller, some instrument clusters remained with the Datsun script featuring on the centre of the speedometer. Nissan tried, with partial success, to cover over the script a grey sticker over the plastic fascia of the instruments, rather than on the speedometer itself. The 1.5-litre engine was dropped from the UK market sometime after the 1986 facelift with the 1.8 becoming the sole engine offered. From the facelift (larger front lights, larger front indicators with additional side repeat indicators, trim improvements, redesigned rear tail light clusters) onwards the UK model was available either in 1.5 GL, 1.8 SGL or 1.8 SGL Anniversary II specification (featuring two-tone paint, electric front windows, electric steel sliding sunroof, power assisted steering and a dealer applied ‘Anniversary II’ badge on the tailgate). The Prairie was sold with a 3-year 100,000 mile warranty and a 6-year anti-corrosion warranty. The European 1.5 produces 70 PS, while the later 2.0 offered 102 PS. Four-wheel-drive was introduced along with the larger engine

Nissan Primera: Since 1986, Nissan had been building Bluebirds — essentially a rebadged home market Auster/Stanza – for the market in Europe at its factory in Washington, Tyne and Wear, England. Nissan showcased the Primera X concept car at the 1989 Tokyo Motor Show as part of Project 901 (Nissan’s performance vision for 1990), and concept car UV.X at the 1989 Frankfurt Motor Show. The design was specifically targeted at European buyers. Having originally launched in Japan in February 1990, Nissan replaced the United Kingdom’s Bluebird with the slightly smaller Primera in September that year. It had a conventional, front-wheel drive chassis and five-speed manual gearbox, with some versions getting the option of a four-speed automatic. Power came from 1.6-litre carbureted (not available in Japan, except in the Avenir Cargo van version) and 1.8-litre and 2.0-litre injection petrol engines. In Europe, a 2.0-litre diesel followed from 1992 onwards, while a 1.6-litre injection gasoline was introduced at the end of 1993. The 1.8 was originally a single point injection model (SR18Di); a multi point injection with more power was added in 1991. The 1.8-litre version was not built with left-hand drive and was not sold in continental Europe. Bodystyles were four- and five-door saloons. A five-door estate was also offered as the Primera Traveller; however, it was based on the slightly different sheet metal of the Nissan Avenir and was only made in Japan. With the exception of the UK GT, only the four-door model was available in Japan. The Primera saw Nissan’s multi link front suspension applied to front-wheel drive for the first time. The 2.0-litre gasoline engine received a power upgrade in 1992, which gave the then ZXe (later renamed the eGT) 150 PS from the standard 2.0-litre engine and a claimed top speed of 219 km/h (136 mph). Some five-door, British made, RHD Primeras were exported back to Japan where they were sold under the name of Primera UK GT. This was the first British-built Japanese car to be reverse-exported back to Japan. In the United States, cars built in Japan was rebadged as the Infiniti G20, part of Nissan’s upper scale Infiniti brand. The G20 was based on the Japanese model Primera, which featured a narrower body to remain within the Japanese compact class tax bracket with width limit at 1.7 m (66.9 in); the Japanese-spec UK GTs also feature the narrower body to comply with the tax bracket. The Primera range came in six trim levels at launch: L, LS, SLX, GS, GSX and ZX. The 1.6-litre engine was available in L, LS and LSX trim and the 2.0-litre 115 PS engine was available in LS, GS and GSX trim. The ZX model had a 2.0-litre 150 PS (148 hp) engine. From 1992 onwards, the range was facelifted and new L, LX, SLX, SGX and eGT trim levels replaced the original naming scheme. A 2.0-litre diesel version was available from 1992. The L cars were basic, and had 1.6-litre petrol engines only. The LX was slightly plusher, but 2.0-litre petrol and diesel versions were also available. SLX was the mid range model, and these also had a choice of 1.6 and 2.0 petrol, or 2.0 diesel engines. The SGX trim level was the luxury specification version; it is powered by the 2.0-litre 115 PS (113 hp) engine. The eGT was the sporting version, with a 2.0-litre 150 PS 8 hp) engine. Engine power was slightly increased during 1994, with the 1.6 model producing 102 PS (101 hp) and the 2.0 model up to 125 PS (123 hp). From 1994, the range received another facelift, and the trim levels were almost the same; although Equation replaced the basic L as the entry level trim; like its predecessor, it had a 1.6 petrol engine, but there was no diesel option. A rare (1,000 examples in Europe) 4×4 option was available, known as a T4 in Japan, with the 150 PS (148 hp) DOHC engine. At this time, the SE replaced the SGX. A new “warm hatch” version, the SRi, joined the line up from 1994. This had a choice of 1.6- or 2.0-litre petrol engines. For the domestic Japanese market there was also a very rare version of the P10 built and tuned by Japanese tuning company Autech: these models came with special Autech suspension and interior packages and a tuned SR20DE 2.0-litre engine making 180 PS. The second-generation Primera was launched in Japan at the end of 1995

Proton Saga: The concept of a ‘Malaysian car’ was conceived in 1979 by Mahathir Mohamad, then the Minister of Trade and Industry.  Mahathir actively encouraged the development of heavy industries in Malaysia as part of a long term vision for self-sufficiency and progress. The automotive industry in Malaysia was established in the late 1960s. Six automobile assembly plants were set up to assemble cars with complete knock-down (CKD) kits imported from various car companies from Europe, America, Japan and Australia. However, inadequate economies of scale and local content regulations drove up prices of new cars in Malaysia over the course of the 1970s, with most if not all locally assembled CKD models generally costing more to produce than an equivalent CBU import. By the dawn of the 1980s, the Malaysian government concluded that direct involvement was necessary to reverse losses and spur future industrial growth. Mahathir Mohamad became the fourth Prime Minister of Malaysia in July 1981. The National Car Project was approved in 1982, with the objective of accelerating technology transfer, increasing and rationalising local content, and involving more Malay entrepreneurs in the then largely ethnic Chinese dominated Malaysian automotive industry. Mahathir had invited Mitsubishi Motors to participate in the National Car Project. The decision to collaborate with a Japanese car company was part of Mahathir’s ‘Look East Policy’. By January 1983, Mitsubishi had prepared two prototypes in Japan, codenamed LM41 and LM44. On 7 May 1983, Perusahaan Otomobil Nasional (Proton) was established. HICOM held a 70% stake in Proton, while Mitsubishi Motors and Mitsubishi Corporation held 15% each. The Proton Saga was launched on 9 July 1985. It is based on the 1983 Mitsubishi Lancer Fiore platform, and powered by the 1.3-litre 4G13 Orion II engine. The first known Proton Saga to roll off the production line in Shah Alam is preserved at the Muzium Negara as a symbol of the beginning of the Malaysian automotive industry. The Saga became a national symbol of Malaysia. Mahathir drove a prototype Proton Saga fitted with a 2.0-litre Mitsubishi Sirius 4G63 engine and a Jalur Gemilang across the Penang Bridge during its opening ceremony on 14 September 1985. Initially, Saga supplies were low, with just 700 vehicles produced in time for the launch. The cars sold quickly, and Proton was unable to meet public demand. However, by mid-1986, the Saga had captured a 64% domestic market share in the Below 1600cc segment. Proton first ventured into export markets in 1986, with Bangladesh receiving the Proton Saga on 26 December 1986, followed by New Zealand, Brunei, Malta and Sri Lanka in 1987. The 10,000th Saga was also produced in 1986. Proton attempted to sell the Saga in the United States as early as 1986 with the help of American automotive entrepreneur Malcolm Bricklin. Mahathir had been impressed by Bricklin, who was advised to work with Proton on orders from the former U.S. Secretary of State, Henry Kissinger, who had previously taught Mahathir at Harvard University Soon after the first Sagas were imported into the United States, Bricklin revealed that he had not gained approval from the authorities. This resulted in the termination of all investments between the involved parties and proved a major financial loss for Proton. In January 1987, the Proton Saga 1.5-litre saloon was introduced. It was powered by the 1.5-litre 4G15 engine, but remained largely unchanged exterior-wise to the 1985 Saga. Later in October 1987, a hatchback variant called the Proton Saga Aeroback was launched. It shared the same 1.5 L engine found in the saloon variant, but featured a redesigned rear end which is unique to Proton. 1987 also witnessed the production of the 50,000th Saga. The Proton Saga Magma was introduced in mid-1987, offering mild mechanical and cosmetic upgrades. The Magma suffix denotes the updated engine, and the Magma-powered Saga can be differentiated from the original Orion II-powered models by its slightly different front grille design and the inclusion of bumper protector mouldings. Additionally, the first Saga models with automatic transmissions were made available in 1987. The Proton Saga made its European debut on 11 March 1988 with its launch in Ireland. Both saloon and hatchback models were made available at a cost of between £8,999 and £10,799. Proton managed to launch the Saga in Ireland before the United Kingdom as only minimal changes and modifications were necessary to pass Irish automotive and safety regulations. Additionally, the Irish automotive market was small at around 50,000 units a year at that period, as opposed to the much larger U.K. market at 2 million units. Proton launched the Saga in several small Commonwealth countries while they prepared for their large scale launch in the U.K. with over 100 dealers. In October 1988, the Proton Saga made its English debut at the 1988 British International Motorshow, where it won three Prestigious Awards (two gold medals and one silver) for quality coachwork and ergonomics. The Saga was also voted among the Top 10 best cars at the show. 1988 witnessed Proton’s entry into the Jamaican market, along with the 100,000th Saga produced. On 16 March 1989, Proton officially launched the Saga saloon and hatchback duo in the United Kingdom.  The saloon models were renamed Proton 1.3 and Proton 1.5 respectively according to their engine displacement in addition to a suffix such as S.E. or G.L. which denoted trim levels. The U.K.-market models also differed slightly from their Malaysian counterparts. All U.K.-market models were equipped with the original Mitsubishi Lancer Fiore dashboard and rear reflector lamps to pass U.K. safety regulations. Britain also received many limited edition models such as the Proton Puma, Lynx, Emerald, Prism and SE Le Mans, which featured higher trim levels and unique equipment. Proton advertised their models with the slogan “Japanese Technology, Malaysian Style” in the United Kingdom. Proton later set the record for the ‘Fastest selling make of new car ever to enter the United Kingdom’, exceeding their 12-month sales target within 6 months. Prior to its launch, the Saga underwent a strict homologation process to be allowed entry and sale in the U.K. market.  The process included various quality, safety and emissions tests and over 400 modifications where necessary, as well as a 1,000 mile-trial on British roads and weather conditions. The Saga also went on sale in Singapore in October 1989. On 12 August 1990, the Proton Saga Megavalve was launched in Malaysia. The Megavalve nameplate represents the third engine update after the Orion (1985–1987) and Magma (1987–1990). The Megavalve engines feature 12-valves or three valves per cylinder, which is an upgrade over the older 8-valve engines. The four additional valves made the new Megavalve engines between 11% and 15% more powerful than the previous Magma plants. The Megavalve engine was produced in both 1.3-litre and 1.5-litre configurations and both were fitted with carburettors. In addition to the updated engines, the Proton Saga Megavalve was also fitted with a new front grille, wrap-around bumper protector moulding and two new exterior colours, namely maroon and green, as well as several minor changes on the interior. The 1.5S model also received new full wheel covers, and Proton reintroduced the Saga Aeroback 1.5I model due to popular demand. Safety standards were also raised with the inclusion of rear seat belts and a third brake light as standard equipment. The Proton Saga Megavalve ranged from RM28,000 to RM36,000, or an increment of RM2,000 over the previous Proton Saga Magma range. A unique limousine version of the Proton Saga was also produced. It is 25 percent longer than the regular Saga saloon, and features a built-in freezer, in-car entertainment system and a television.  The 200,000th Saga rolled off the production line on 16 May 1990. Proton launched the facelifted Proton 12-Valve in the United Kingdom on 10 January 1991. The power output from the 1.3 L engine was upped to 77 bhp and the 1.5 L offered 85 bhp. On 22 September 1991, the Proton Saga won two gold awards at the British International Motorshow for the second time. The Saga was also launched in Malawi in December 1991. By then Proton had managed to export 40,151 units, of which 33,291 were to the United Kingdom, with 3,699, 1,160 and 847 to Singapore, Ireland and New Zealand respectively. The 300,000th Saga was also produced in 1991, and locally manufactured Saga parts rose to 69% after the opening of the Engine and Transmission Factory in Shah Alam.  A facelifted version was launched in August 1992, and in this guise the car was produced until 2003, though UK market sales dwindled quite sharply in the mid 90s, that initial success proving to be relatively short lived.

Renault R20TX: Launched in March 1975, the Renault 30 TS was the first Renault with an engine having more than four cylinders since before World War II. It was one of the first cars (the other two being the Peugeot 604 and Volvo 264) to use the then newly introduced 2664 cc PRV V6 engine, which was developed jointly between Peugeot, Renault and Volvo; the PRV produced 130 PS and could power the R30 to a top speed of 185 km/h (115 mph). The vehicle’s hatchback styling was derivative of the extremely successful Renault 16. The more affordable Renault 20 was presented at the Paris Salon in November 1975 used the same hatchback body styling as the R30 but with two rectangular headlights instead of the R30’s quadruple round lights. The Renault 20 was essentially a replacement for the discontinued Renault 16, albeit in a rather larger body shell. Under the bonnet, the R20 had the smaller four-cylinder 1647 cc engine (from the Renault 16 TX) rated at 90 PS. Other technical differences between the 20 and 30 were that 20 used drum brakes at the rear wheels, 13 inch wheel rims, and a smaller 60-litre fuel tank. The 20 came in three different trim variations: L, TL and GTL. The two cars were effectively two ‘badge engineered’ versions of the same car with separate numeric classification. The R20 received an all-new 2068 cc diesel engine in November 1979, Renault’s first diesel automobile. Both the 20 and 30 were advanced in terms of safety, featuring front and rear crumple zones as well as side impact protection. Reliability issues, such as niggling mechanical faults (which sometimes proved expensive to fix) plagued both cars throughout their lifetimes. Rust was another major concern (in a Belgian owner referendum 70% of owners named it as the car’s biggest problem); as a response Renault improved rust protection and began offering a five-year warranty against rust on 1 January 1982. Shortly after their introduction, it soon became quite clear that the Renault 20 was too underpowered to cope with the overall size and weight of the car and that the Renault 30 was seen as too expensive for what was effectively the same car. In response to this, the R20TS was introduced, and used a new four-cylinder 1995 cc overhead camshaft engine rated at 109 PS (which was shared with the Citroën CX and later the Peugeot 505). The new 2.0-litre engine was universally regarded as a big improvement. The following year (October 1978) saw the introduction of the R30 TX, a more luxurious fuel-injected version of the R30 TS, then the R20 Diesel in late 1979. By late 1981, all 1.6-litre R20s were discontinued, leaving the LS 2.0 as the smallest model in the range. In 1980 the NG1 five-speed transmission was switched for the longer-geared and smoother shifting 395 unit. In July 1980, the 2.2-litre fuel-injected R20 TX was added to the range, followed by the R30 Turbo Diesel one year later. The R30 Diesel Turbo has the trim of the R30 TX, albeit with unique alloys, with an engine delivering 85 PS derived from the naturally aspirated diesel engine. In a few markets this engine was also available as an R20. The range was facelifted for the 1981 model year. Production of the 20 and 30 ceased on 16 October 1983 to make way for the Renault 25.

Toyota Crown: Launched in February 1971, the 4M 2600 engine was introduced with this generation, as was the luxurious Super Saloon trim level, followed by the Super Deluxe and Deluxe. The top-of-the-line Royal Saloon was first introduced in the facelifted Crown from 1973, adding luxury features from the Century limousine. The 2.0-litre 5R inline-four engine and the 2.0-liter M six-cylinder engine were also available. As for the previous generation, the M-C engine (in Japanese specifications) has 104 bhp, while the 5R’s output increased somewhat to 97 bhp. In some markets the previous 2.3-litre “2M” six remained available, in sedan or “utility wagon” forms. The Utility Wagon was a version halfway between commercial and passenger car, and had chassis codes MS67V until the early 1973 facelift when it was replaced by the MS68V with the 2.6 engine. Previous generations of the Crown had been marketed under the Toyopet name but the fourth-generation model was the first version to be officially known worldwide as the Toyota Crown. The Sedan and Wagon (Custom) are coded RS60/MS60/MS64/MS65 and MS62/MS63, while the Van was coded MS66V with the two litre “six”. The Hardtop Coupé is MS70 (2.0-litre), or MS75 (2.6-litre). The Japanese market Crown Custom (Wagon) was classified as a seven-seater. This generation was the first Crown marketed as a Toyota in Japan, as previous models were marketed as Toyopets. Also, in Japan, this model was known as the “whale” or “kujira” Crown. In 1973, Japanese television commercials introduced Japanese actress Sayuri Yoshinaga as a co-spokeswoman, joining Satoshi Yamamura, and together they appeared in commercials until 1983. While the domestic market Hardtop has rectangular halogen headlights, all export models come with twin round headlights. This model achieved few sales in the US due to its high price when compared to competing domestic models, and possibly its styling with flush bumpers, called “spindle-shaped” in period marketing. Only the first two years were imported to North America, where it was the last Crown to be sold until 2022. The Corona Mark II replaced the Crown in North America. The boot could be opened remotely by turning the ignition key to the far left, and a button on the floor caused the radio to engage the signal seeking feature. A separate signal seeking feature was installed for rear seat passengers, installed behind the front seat facing the rear seat compartment. The 60-series Crown underwent a facelift in January 1973. Australian models were assembled in Australia by AMI. It was available in New Zealand fully imported from 1971 to 1973, with local assembly beginning at Steels Motor Assemblies, who also built the Corona, not long before the mid-life facelift, improving availability. Steels subsequently became Toyota NZ’s Christchurch CKD assembly plant. The replacement model debuted in Japan in 1974 and reached export markets the following year.

Toyota Corona Liftback: Introduced in Japan in September 1978, the T130 series Corona adopted a boxier design over the outgoing T100/110/120 series. It maintained the standard front-engine / rear-wheel-drive layout of all Coronas that preceded it. The T130 series was available in a wide range of body styles across various markets including a four-door sedan, two-door hardtop coupe, four-door wagon and new five-door liftback, which featured a 40:60 split fold rear seat. The assignment of “T130” to all Corona body styles signified a new approach from having different series number identifiers for the various body styles. This was also the first Corona to be sold as a “Toyota” rather than a “Toyopet” in the Japanese domestic market. All models featured MacPherson strut independent front suspension as well as a four-link trailing arm rear suspension arrangement with a Panhard rod, except for the wagon, which used leaf springs, like the Corolla and Cressida wagons. Disc brakes were fitted as standard equipment on the front of all models. Rear disc brakes were fitted as standard on the 2000GT and 2000SL, which were not available to all international markets. Other models were fitted with rear drum brakes. The Corona range received a thorough facelift in August 1980, with new rearwards sloping rectangular headlights which gave it a more modern appearance at the front. The T130 series was manufactured with a wide range of engine and transmission combinations. 1.6-litre 12R, 2T (and associated 12T) and 2.0-litre 18R engines are the most common. The LPG-powered 12R engine became available in the Japanese domestic market in February 1979 and, along with the LPG-powered 5R engined model, continued to be built until August 1982. The rest of the Corona range was taken out of production for the Japanese market in December 1981. Amongst other minor changes, the 1.8-litre 3T / 13T engine was added in 1981 to replace the 1.6-litre 2T/12T. The North American Corona shared the 2.2-litre 20R engine with the Celica. Emission regulations passed in 1978 were applied across the range of models offered. The 1.8L engine was equipped with electronic fuel injection as well as the 2.0L engine. In Japan the venerable 2.0L 18R-G was offered in the range-topping 2000GT, developing 101 kW (135 hp) at 5800 rpm. The station wagon was, as usual at the time, marketed as a “light van” in Japan. This was registered as a commercial vehicle for certain tax benefits and less restrictive emissions standards. When introduced, the Corona Van was available as a 1600 (TT137V) or an 1800 (RT137V), both using engines not installed in the rest of the range. The 2T-J in the 1600 Standard produces 93 PS at 6000 rpm while the DX and GL models’ 1.8-litre 16R offered 95 PS at 5600 rpm but with considerably more torque. The 2T and 16R were both replaced by the newer 12T-J engine in December 1979, reflecting newly tightened emissions standards for commercial vehicles in Japan. This model, the TT138V, produces 86 PS at 5600 rpm. Only the Liftback was sold in the UK, from the summer of 1979. Production of the T130 ended in 1982, to be replaced by the T140 series.

Toyota Tercel 4WD Estate: Toyota redesigned the Tercel in May 1982, now called the Tercel in all markets. Its internal model code is the L20 series. It was available in three- or five-door hatchback models or a four-door station wagon, and also as a four-door sedan in Japan. The station wagon, known in Japan as the Sprinter Carib (Japanese: Toyota Sprinter Carib, short for “caribou”, was introduced in August 1982. The wagon was also available with four-wheel drive (front-wheel-drive wagons were only available in select markets). The new Tercel 4WD was built from existing pieces in the Toyota inventory. The engine, transaxle and front-wheel-drive system were from the existing Tercel; the longitudinally mounted engine made such a conversion a simple affair. The coil-sprung, live rear axle and the drive shaft was taken from the rear-wheel drive Corolla. The only major part specifically designed for the new Tercel 4WD was the transfer case, built into the transmission. The transfer case provides the driver with three different power arrangements: Normally, the car is operated with front-wheel drive. When the driver pulls the 4WD selector lever back into four-wheel drive, or presses a button on the gear selector for the automatic transmission, front and rear differentials are driven at the same RPM via a direct mechanical coupling. There is no conventional centre differential, so the four-wheel-drive system can be used only on loose or slippery road surfaces (such as snow, gravel, or sand); otherwise the drivetrain experiences severe wear, and handling is compromised. The third power option (which was only available on the six-speed manual) is low range. This is not the same as the low-range power option found in a truck or conventional SUV, as the Tercel lacks a high-range-low-range transfer case. When the lever is placed in four-wheel-drive mode it becomes possible to down shift the vehicle from first to EL. In 1985, there were minor changes to gear ratios and to the grille design, and the interior was updated in 1986. The Tercel wagon (and four-door sedan in Japan) continued with the same design until February 1988 (when the Sprinter Carib was replaced by a larger, Corolla-based design), while the sedans and hatchbacks moved on to the newer design.

Vauxhall Royale: The Senator A and Monza were initially sold in the United Kingdom as the Vauxhall Royale (and Vauxhall Royale Coupé). Unlike other members of the joint Opel/Vauxhall model programme of the period, the Royale was simply a badge engineered version of the Senator with only detail differences from its Opel sister. Following the merger of the UK Opel and Vauxhall dealer networks in 1982, the Opel marque was repositioned as a performance-luxury brand, and the Vauxhall Royale models were dropped in favour of the Opel Senator/Monza, coinciding with the “A2” mid-cycle facelift. This policy was reversed in late 1984, with the Senator reverting to Vauxhall branding for the 1985 model year, but the Monza remained on sale as an Opel until its discontinuation at the end of 1987.

VW Santana: The Volkswagen Santana is a nameplate used by Volkswagen for various sedans and station wagons since 1983. The first generation was based on the second-generation Volkswagen Passat (B2). It was introduced in 1981 while production started in 1983 for China and 1984 for Europe. The use of the “Santana” badge rather than “Passat” echoes the use of different names for the sedan versions of the Polo (Derby) and Golf (Jetta). It was positioned initially in the UK as a more up-market car and came only with the 5 cylinder engine and the poshest trim. When VW facelifted the model, they renamed it the Passat Saloon. Whilst the car had a short life in Europe, it lived on for many years in China where it became a staple of the VW range.

Wartburg Knight: The Wartburg 353, known in some export markets as the Wartburg Knight, is a medium-sized family car produced by the East German car manufacturer AWE for their Wartburg brand. It was the successor of the Wartburg 311 and was itself succeeded by the Wartburg 1.3. The Wartburg 353 was produced from 1966 to 1988, becoming the Wartburg with the longest production run. During its lifetime, it saw several changes and improvements, the most recognizable of which came in 1985 with a front facelift (as pictured here), a slightly different layout around the engine block, and a new carburettor. First introduced in June 1966, the Wartburg 353 was the creation of the former German BMW production facilities (called EMW under Soviet occupation). Its origins were ultimately derived from a 1938 DKW design and powered by a two-stroke engine with only seven major moving parts: three pistons, three connecting rods and a crankshaft. This led to a common aphorism among Wartburg owners, which is that “one drives a car, but only has to maintain a motorcycle.” Domestically, it was used for all government transportation, sometimes as a Volkspolizei police car. However, due to the nature of the planned economy, deliveries to private owners could take ten to fifteen years. Like other Eastern Europe cars, it was known for its low price in export markets. Because of its forward centre of gravity and front-wheel drive, the car had typical front-wheel-drive road handling, usually displaying significant understeer, especially in wet conditions. Wartburgs were exported to most European markets and South Africa. The Wartburg 353 was powered by a 1-litre displacement, 3-cylinder unit that took almost two decades to refine. While developing about 50 to 55 PS (depending on the carburettor type), its two-stroke engine design provided more than 100 Nm of torque (106 Nm in the last version), which was a typical figure for many larger four-stroke engines at that time. The transmission was equipped with a freewheel, obviating the need to use the clutch between gears. Designed as a fuel efficiency measure and as a means of protecting the engine from oil starvation due to the nature of 2-strokes, the device disabled engine braking; the car could coast whenever the throttle was released. Drivers could turn the freewheel off through a switch under the steering column to benefit from engine braking, which was useful since the front brakes were prone to overheating and fading. However, most drivers never disabled the freewheel because it made shifting gears significantly easier and smoother, though not quicker. Earlier models had the gear stick on the steering column, although later versions had it on the floor. Today, 353s are customized for reaching speeds well about 200 km/h (125 mph), whereas the original design called for critical speed of 150–155 km/h (93–96 mph) and 12 seconds to accelerate to 100 km/h (62 mph), which was dealt with in second gear due to the high-revving engine. It was available with four- and five-speed transmissions, although the latter was rare. The 353 was a reasonable success throughout the Eastern bloc, with front-wheel drive. Its negatives were due to its outmoded two-stroke engine. However, in the Western European markets, the Wartburg was quite competitive especially because of its high maximum power of 58 hp at 5400rpm and top speed of 170km/h which is uncommon for passenger cars in the West, despite the two-stroke engine design. The last modernization of Wartburg took place in 1988 when the car got the new designation “1.3” and a four-stroke VW-designed engine with a 1.3-liter displacement. In 1991, Opel bought the plant. Although the low price militated against the owners taking care of the car. Resale values were extremely low, and in Finland, official figures on removals from the car register gave Wartburg the shortest average life span of all listed manufacturers; this due to German reunification; the car ceased production in 1991 at nine years and three months. The Wartburg 353 was commonly nicknamed “Trustworthy Hans” or “Farty Hans” by owners due to its durability and copious exhaust emissions, especially when cold and/or overoiled. Noteworthy characteristics of the model are simple design, dependability, occasional and cheap maintenance, strong chassis-based car frame, front-wheel drive, rear-wheel ABS regulator, a 525-litre trunk, and innovative electronic gauges fitted after 1983. Disadvantages in terms of passengers’ comfort are well known too: lack of any sound dampers led to significant engine feedback in the coupe, which was in turn very boomy and reverberating, leading to another nickname, “The barrel”. This left very few Wartburgs equipped with stereo because it was not possible to enjoy that at volumes most people do, over the engine noise. The suspension provided sensibly different handling and comfort when the car was empty and carrying passengers and luggage. Owners’ accounts are that control and smoothness improved the more the car was loaded. It was also available as a pickup version named Wartburg 353 Trans but was unsuccessful, mainly due to limited payload (only 450 kg) and low transport volume. It was mainly used for small deliveries. This car was only sold for export, as it would have been useful mostly to the illegal private business endeavours in East Germany. Over a million Wartburg 353s were produced overall

Wolseley: this is the very short-lived Wolseley version of the ADO71. It was announced in March 1975 with the less plush versions, but by September when the range became the Princess, it ceased production. Mechanically it carried much forward from the Six which it replaced, including the 6 cylinder E Series 2226cc engine all clothed in the futuristic looking body.

NEW CARS and the ELECTRIC VILLAGE

The emphasis here was very much on electric cars, and a number of manufacturers had both display cars and ones that you could take out for a short test drive. Needless to day, this was a popular activity and if you wanted a specific car, you needed to book in early.

ABARTH

This would be the first chance for many to see the new all-electric Abarth 500e as the model is only just arriving on UK shores. The Abarth New 500e Scorpionissima is a performance variant that made its official debut on 22 November 2022, featuring unique scorpion-badged alloy wheels. Initially, it is being released in a Scorpionissima edition limited to 1,949 examples. Scorpionissima models will be available in a choice of Acid Green or Poison Blue colours, bearing unique side graphics and wheels. The first deliveries were scheduled for June 2023. It has a single electric traction motor that produces 114 kW (153 hp) and 235 Nm (173 lb/ft), an increase of 26.7 kW (35.8 hp) and 15 Nm (11 lb/ft) over the standard motor, and accelerates from 0 to 100 km/h (62 mph) in 7 seconds.  The enhancements in power and torque output are derived from improved inverter and battery wiring, and a reduction in the final-drive ratio. The Abarth also swaps the rear drum brakes on the New 500 for discs. Three driving modes are offered: Turismo, Scorpion Street, and Scorpion Track; output power and torque are limited to 100 kW (130 hp) and 220 Nm (160 lb/ft) in Turismo. Scorpion Street maximizes regenerative braking, simulating the engine braking effect of a conventional car equipped with a manual transmission, while Scorpion Track sacrifices range for performance. In manufacturer testing at Balocco, the Abarth 500e is able to complete laps 1 second quicker than the Abarth 695. Total weight is 1,410 kg (3,110 lb), including the 295 kg (650 lb) battery. Charging hardware is carried over from the regular New 500 equipped with the larger battery, at rates up to 85 kW. The Abarth 500e has a battery with a capacity of 42.2 kWh (gross) and 37.3 kWh (net), giving the vehicle a claimed range of 264 km (164 mi) under the WLTP driving cycle with the standard 17-inch wheels; equipping the 18-inch wheels reduces range to 253 km (157 mi). Real-world mixed driving with 18-inch wheels indicated an actual range of 212 km (132 mi), with consumption of 3.4 mi/kWh.

ALFA ROMEO

The production Tonale was originally scheduled for release in 2021, but was delayed until 2022 due to the global semiconductor shortage and Alfa Romeo management demanding better range and performance from its drivetrain. It was developed during the ownership of Fiat Chrysler Automobiles and underpinned by a heavily modified version of the SCCS crossover platform shared with the Jeep Compass. It is also the first Alfa Romeo to be equipped with an optional plug-in hybrid system, which uses a 15.5 kWh (56 MJ) lithium-ion battery to achieve 30 miles (48 km) of all-electric range. The Tonale marks the brand’s electrification effort, where Alfa Romeo will be the first brand among the 14 brands of Stellantis to go fully electric by 2027. The Tonale is marketed in the premium segment, and has been described variously as a “compact crossover”, a “compact SUV”, a “small SUV”, and a “tall hatchback”. All models of the Tonale are equipped with a 12.3-inch (31 cm) digital infotainment cluster and a 10.25-inch (26.0 cm) infotainment screen, which will run on the Uconnect 5 software suite. In addition, the Tonale will come with an NFT that records and stores data of the car’s life cycle. According to Alfa Romeo, the NFT will generate a certificate that Stellantis claims can help maintain the car’s residual value. The Verge noted that Alfa Romeo had not provided much information about what blockchain technology they intended to use for this. Jalopnik felt that digitising a car’s service history was a good idea, but that blockchain NFTs were a “bad” and “entirely unnecessary” way to achieve this. According to Alfa Romeo, the Tonale was designed to offer more driving engagement than the class average by using a very quick steering rack (2.3 turns lock-to-lock). It also features torque vectoring by braking, frequency-selective dampers as standard, and adaptive items and four-piston brakes on the range-topping Veloce. UK sales started in late 2022 and the car is starting to appear at Italian car events now.

ALPINE

Alpine had a number of examples of the highly-rated but slow-selling A110 here.

GENESIS

Although still a rare sighting on UK roads, Genesis has a large range of cars, ranging from executive saloons to plush crossovers, some with ICE propulsion and others all-electric.

POLESTAR

Making an appearance here was not just the familiar Polestar 2 but also the next couple of additions to the range, the Polestar 3 and Polestar 4.

BRDC PARKING

Members of the BRDC have their own parking around the back of their own building, and it is always worth having a look to see what treasures are to be found parked up here. I went to have a look a couple of times, and that yielded these cars, most of which were further examples of cars I had seen elsewhere on site but there were some really special cars here as well. There is another building down by the international pits and some of these cars could also be seen parked up by that during the course of the weekend

ABARTH

There was another example here of the S4 version of the 595.

ALFA ROMEO

In the mid-1920s, Alfa’s RL was considered too large and heavy, so a new development began. The 2-litre formula that had led to Alfa Romeo winning the Automobile World Championship in 1925, changed to 1.5-litre for the 1926 season. The 6C 1500 was introduced in 1925 at the Milan Motor Show and production started in 1927, with the P2 Grand Prix car as starting point. Engine capacity was now 1487 cc, against the P2’s 1987 cc, while supercharging was dropped. The first versions were bodied by James Young and Touring.  In 1928, a 6C Sport was released, with a dual overhead camshafts engine. Its sport version won many races, including the 1928 Mille Miglia. Total production was 3000 (200 with DOHC engine). Ten copies of a supercharged (compressore) Super Sport variant were also made. The more powerful 6C 1750 was introduced in 1929 in Rome. The car had a top speed of 95 mph, a chassis designed to flex and undulate over wavy surfaces, as well as sensitive geared-up steering. It was produced in six series between 1929 and 1933. The base model had a single overhead cam; Super Sport and Gran Sport versions had double overhead cam engines.  Again, a supercharger was available. Most of the cars were sold as rolling chassis and bodied by coachbuilders such as Zagato, and Touring. Additionally, there were 3 examples built with James Young bodywork. In 1929, the 6C 1750 won every major racing event it was entered, including the Grands Prix of Belgium, Spain, Tunis and Monza, as well as the Mille Miglia was won with Giuseppe Campari and Giulio Ramponi, the Brooklands Double Twelve and the Ulster TT was won also, in 1930 it won again the Mille Miglia and Spa 24 Hours. Total production was 2635.

Also here were further examples of the 105 series GTV.

ASTON MARTIN

Needing little in the way of introduction, as thanks to its starring role with James Bond, this has to be one of the world’s most recognised cars, is the DB5, a couple of examples of which were on show. The DB5 was designed by the Italian coachbuilder Carrozzeria Touring Superleggera. Released in 1963, it was an evolution of the final series of DB4. The principal differences between the DB4 Series V and the DB5 are the all-aluminium engine, enlarged from 3.7 litre to 4.0litre; a new robust ZF five-speed transmission (except for some of the very first DB5s);and three SU carburettors. This engine, producing 282 bhp, which propelled the car to 145 mph, available on the Vantage version of the DB4 since March 1962, became the standard Aston Martin power unit with the launch in September 1963 of the DB5. Standard equipment on the DB5 included reclining seats, wool pile carpets, electric windows, twin fuel tanks, chrome wire wheels, oil cooler, magnesium-alloy body built to superleggera patent technique, full leather trim in the cabin and even a fire extinguisher. All models have two doors and are of a 2+2 configuration. Like the DB4, the DB5 used a live rear axle. At the beginning, the original four-speed manual (with optional overdrive) was standard fitment, but it was soon dropped in favour of the ZF five-speed. A three-speed Borg-Warner DG automatic transmission was available as well.  The automatic option was then changed to the Borg-Warner Model 8 shortly before the DB6 replaced the DB5. The high-performance DB5 Vantage was introduced in 1964 featuring three Weber twin-choke 45DCOE side-draft carburettors and revised camshaft profiles, delivering greater top-end performance at the expense of overall flexibility, especially as legendary Webers are renowned as ‘full-throttle’ devices. This engine produced 315 hp. Only 65 DB5 Vantage coupés were built. Just 123 convertible DB5s were produced (also with bodies by Touring), though they did not use the typical “Volante” name until 1965.  The convertible model was offered from 1963 through to 1965. Originally only 19 of the 123 DB5 Convertibles made were left-hand drive. 12 cars were originally fitted with a factory Vantage engine, and at least one further convertible was subsequently factory fitted with a DB6 specification Vantage engine. A rare factory option (actually fitted by Works Service prior to customer delivery) was a steel removable hard top. From October 1965 to October 1966, Aston Martin used the last 37 of the Aston Martin DB5 chassis’ to make another convertible model. These 37 cars were known as “Short Chassis” Volantes and were the first Aston Martins to hold the “Volante” name. Although calling it a “Short Chassis” is a bit of a misnomer as the “short” comes from comparing it to the subsequent DB6, which has a longer chassis. When compared to the DB5, it is not “short” but rather the same size, however these cars differ to the DB5 convertible models as they feature DB6 split front and rear bumpers and rear TR4 lights, as also used on the DB6. These days the DB5 is the most valuable of all the DB models from the 1960s, with many of them heading towards the £1 million pound mark.

BENTLEY

Bentley replaced the 3 Litre with a more powerful car by increasing its engine displacement to 4.5 litres. As before, Bentley supplied an engine and chassis and it was up to the buyer to arrange for their new chassis to be fitted with one of a number of body styles, most of which were saloons or tourers. Very few have survived with their four-seater coachwork intact. WO Bentley had found that success in motorsport was great publicity for the brand, and he was particularly attracted to the 2 Hours of Le Mans endurance race, the inaugural running of which took place 26–27 May 1923, attracting many drivers, mostly French. There were two foreign competitors in the first race, Frank Clement and Canadian John Duff, the latter winning the 1924 competition in his personal car, a Bentley 3 Litre. This success helped Bentley sell cars, but was not repeated, so after two years without success, Bentley convened a group of wealthy British men, “united by their love of insouciance, elegant tailoring, and a need for speed,” to renew Bentley’s success. Both drivers and mechanics, these men, later nicknamed the “Bentley Boys”, drove Bentley automobiles to victory in several races between 1927 and 1931, including four consecutive wins at the 24 Hours of Le Mans, and forged the brands reputation. It was within this context that, in 1927, Bentley developed the Bentley 4½ Litre. Two cylinders were removed from the 6½ Litre model, reducing the displacement to 4.4 litres. At the time, the 3 Litre and the 6½ Litre were already available, but the 3 Litre was an outdated, under-powered model and the 6½  Litre’s image was tarnished by poor tyre performance. Sir Henry “Tim” Birkin, described as “the greatest British driver of his day” by W. O. Bentley, was one of the Bentley Boys. He refused to adhere strictly to Bentley’s assertion that increasing displacement is always preferable to forced induction. Birkin, aided by a former Bentley mechanic, decided to produce a series of five supercharged models for the competition at the 24 Hours of Le Mans; thus the 4½ litre Blower Bentley was born. The first supercharged Bentley had been a 3-litre FR5189 which had been supercharged at the Cricklewood factory in the winter of 1926/7. The Bentley Blower No.1 was officially presented in 1929 at the British International Motor Show at Olympia, London. The 55 copies were built to comply with 24 Hours of Le Mans regulations. Birkin arranged for the construction of the supercharged cars having received approval from Bentley chairman and majority shareholder Woolf Barnato and financing from wealthy horse racing enthusiast Dorothy Paget. Development and construction of the supercharged Bentleys was done in a workshop in Welwyn by Amherst Villiers, who also provided the superchargers. W.O. Bentley was hostile to forced induction and believed that “to supercharge a Bentley engine was to pervert its design and corrupt its performance.” However, having lost control of the company he founded to Barnato, he could not halt Birkin’s project. Although the Bentley 4½ Litre was heavy, weighing 1,625 kg (3,583 lb), and spacious, with a length of 172 in and a wheelbase of 130.0 in, it remained well-balanced and steered nimbly. The manual transmission, however, required skill, as its four gears were unsynchronised. The robustness of the 4½ Litre’s latticed chassis, made of steel and reinforced with ties, was needed to support the heavy cast iron inline-four engine. The engine was “resolutely modern” for the time. The displacement was 4,398 cc. Two SU carburettors and dual ignition with Bosch magnetos were fitted. The engine produced 110 hp for the touring model and 130 hp for the racing model. The engine speed was limited to 4,000 rpm. A single overhead camshaft actuated four valves per cylinder, inclined at 30 degrees. This was a technically advanced design at a time where most cars used only two valves per cylinder. The camshaft was driven by bevel gears on a vertical shaft at the front of the engine, as on the 3 Litre engine. The essential difference between the Bentley 4½ Litre and the Blower was the addition of a Roots-type supercharger to the Blower engine by engineer Amherst Villiers, who had also produced the supercharger. W. O. Bentley, as chief engineer of the company he had founded, refused to allow the engine to be modified to incorporate the supercharger. As a result, the supercharger was placed at the end of the crankshaft, in front of the radiator. This gave the Blower Bentley an easily recognisable appearance and also increased the car’s understeer due to the additional weight at the front.  A guard protected the two carburettors located at the compressor intake. Similar protection was used, both in the 4½ Litre and the Blower, for the fuel tank at the rear, because a flying stone punctured the 3 Litre of Frank Clement and John Duff during the first 24 Hours of Le Mans, which contributed to their defeat. The crankshaft, pistons and lubrication system were special to the Blower engine. It produced 175 hp at 3,500 rpm for the touring model and 240 hp at 4,200 rpm for the racing version, which was more power than the Bentley 6½  Litre developed. Between 1927 and 1931 the Bentley 4½  Litre competed in several competitions, primarily the 24 Hours of Le Mans. The first was the Old Mother Gun at the 1927 24 Hours of Le Mans, driven as a prototype before production. Favoured to win, it instead crashed and did not finish. Its performance was sufficient for Bentley to decide to start production and deliver the first models the same year. Far from being the most powerful in the competitions, the 4½ Litre of Woolf Barnato and Bernard Rubin, raced neck and neck against Charles Weymann’s Stutz Blackhawk DV16, setting a new record average speed of 69 mph; Tim Birkin and Jean Chassagne finished fifth. The next year, three 4½ Litres finished second, third, and fourth behind another Bentley, the Speed Six, which possessed two more cylinders.The naturally aspirated 4½ Litre was noted for its good reliability. The supercharged models were not; the two Blower models entered in the 1930 24 Hours of Le Mans by Dorothy Paget, one of which was co-driven by Tim Birkin, did not complete the race. In 1930, Birkin finished second in the French Grand Prix at the Circuit de Pau behind a Bugatti Type 35. Ettore Bugatti, annoyed by the performance of Bentley, called the 4½ Litre the “fastest lorry in the world.” The Type 35 is much lighter and consumes much less petrol. Blower Bentleys consume 4 litres per minute at full speed. In November 1931, after selling 720 copies of the 4½ Litre – 655 naturally aspirated and 55 supercharged – in three different models (Tourer, Drophead Coupé and Sporting Four Seater, Bentley was forced to sell his company to Rolls-Royce for £125,175, a victim of the recession that hit Europe following the Wall Street Crash of 1929.

There was another example of the Arnage here, also.

DAIMLER

Launched late in 1962, the Daimler V8 Saloon was essentially a rebadged Jaguar Mark 2 fitted with Daimler’s 2.5-litre 142 bhp V8 engine and drive-train, a Daimler fluted grille and rear number plate surround, distinctive wheel trims, badges, and interior details including a split-bench front seat from the Jaguar Mark 1 and a black enamel steering wheel. Special interior and exterior colours were specified. Most cars were fitted with power-assisted steering but it was optional. Automatic transmission was standard; manual, with or without overdrive, became an option in 1967. The 2.5 V8 was the first Jaguar designed car to have the Daimler badge. A casual observer, though not its driver, might mistake it for a Jaguar Mark 2. The Daimler’s stance on the road was noticeably different from a Mark 2. In April 1964 the Borg-Warner Type 35 automatic transmission was replaced by a D1/D2 type, also by Borg-Warner. A manual transmission, with or without an overdrive unit usable with the top gear, became available on British 2.5 V8 saloon in February 1967 and on export versions the following month. Cars optioned with the overdrive had the original 4.55:1 final drive ratio. In October 1967, there was a minor face-lift and re-labelling of the car to V8-250. It differed only in relatively small details: “slimline” bumpers and over-riders (shared with the Jaguar 240/340 relabelled at the same time), negative-earth electrical system, an alternator instead of a dynamo and twin air cleaners, one for each carburettor. Other new features included padding over the instrument panel, padded door cappings and ventilated leather upholstery, reclinable split-bench front seats and a heated rear window. Power steering and overdrive were optional extras. Jaguar replaced its range of saloons—the 240, the 340, the 420, and the 420G—with the XJ6 at the end of 1968. The company launched the XJ6-based Daimler Sovereign the following year to replace the Daimler saloons—the 240-based V8-250 and the 420-based Sovereign. Henceforth all new Daimlers would be re-badged Jaguars with no engineering links to the pre-1960 Daimlers.

FERRARI

This looks like an  F40 LM. The racing cars were prepared by Michelotto (based in Padua) the Ferrari specialist who had already carried out work on the GTO Evoluzione and on parts of the road-going version of the F40. Three chassis were prepared and two were used in races, with serial numbers 79890 and 79891. The third chassis, with serial number 88521, was intended to be raced and was a spare car that stayed at Michelotto but was never raced. The car saw competition as early as 1989 when it debuted in the Laguna Seca Raceway round of the IMSA, appearing in the GTO category, with an LM evolution model driven by Jean Alesi, finishing third to the two faster spaceframe four wheel drive Audi 90s and beating a host of other factory-backed spaceframe specials that dominated the races. In the following race, it had to retire after eighteen laps. The next IMSA season, driven by a host of guest drivers such as Jean-Pierre Jabouille, Jacques Laffite and Hurley Haywood, three second-places and one third-place were the best results. Although the F40 would not return to IMSA in 1991, it would later be a popular choice by privateers to compete in numerous domestic GT series including JGTC. In 1994, the car made its debut in international competitions, with one car campaigned in the BPR Global GT Series by Strandell, winning at the 4 Hours of Vallelunga. In 1995, the number of F40s climbed to four, developed independently by Pilot-Aldix Racing (F40 LM) and Strandell (F40 GTE, racing under the Ferrari Club Italia banner), winning the 4 Hours of Anderstorp. No longer competitive against the newly entered McLaren F1 GTR, the Ferrari F40 returned for another year in 1996, managing to repeat the previous year’s Anderstorp win, and from then on it was no longer seen in GT racing. In total nineteen cars were produced.

In addition there were further examples of the 550 Maranello, its successor the 599 GTB and the 488 Pista.

FRAZER NASH

The Frazer Nash Le Mans Replica, and its evolution, the Frazer Nash Le Mans Replica Mk2, is a sports car, designed, developed and built by British manufacturer Frazer Nash, between 1949 and 1954.

HOLDEN

HSV

LAND ROVER

The Lightweight 1/2 ton was a British military vehicle supplied by Land Rover. It was a vehicle designed to be light enough to be carried by the Westland Wessex, a medium-lift helicopter in service for over 40 years with the U.K armed services. It was produced from 1968 to 1984, and served widely internationally and in private use. In the early 1960s both the Royal Marines, then largely based aboard commando carriers, and the British Army required a vehicle that could be carried by air to replace the Austin Champ. They had taken delivery of the Westland Wessex helicopter, which could carry a 2,500 lb (1,134 kg) load slung beneath. The smallest Land Rover available at the time was a Series IIA 88 inch (2235 mm) wheelbase, which was too heavy. Land Rover began work on a lightweight version to fit the specifications in 1965. A new modification to the basic Series IIA was devised by making many body components easily detachable and removing many non-essential items. The result was the Land Rover Half-Ton, known widely as the Lightweight or Airportable. In practice, to reduce weight sufficiently for the helicopters of the day to lift them in combat conditions, the tilt (roof) and sticks, the upper parts of the body, the doors and windscreen were removed, to be refitted later. The most significant change, however, was a reduction in width by 4 inch (100 mm), by redesigning the standard Series IIA axles and fitting shorter half-shafts, which meant it would fit on a standard pallet. Complete, the 24 Volt FFR Lightweight IIA had an unladen weight of 3,329 lb (1,510 kg), which was over the specified weight. The term Lightweight appears misleading as a standard 88 Land Rover weighed 1,318 kg (2,906 lb), but the higher total weight was due to the various frame reinforcement required for military usage.[2] However, with the removable body panels taken-off it the 24 Volt FFR weighed 2,808 lb (1,274 kg) below the limit. Since improvements to the helicopters meant more lift was available, the MoD accepted it for use. The main applications were actually to be shipped by cargo aircraft or stacked on train wagons, with helicopter transport a rare occurrence. The first production models were completed on 11 November 1968, and production continued until 1984. Although a very few prototypes had been built between 1965 and 1967, and about six pre-production models early in 1968, ‘Lightweight’ Series IIA quantity production began on 11 November 1968, with a total of 15 vehicles being produced on that day. Total production of Series IIa ‘Lightweights’ was between 1,500 and 2,000 vehicles. Later Series IIa models had the headlamps moved out into a revised front wing, to comply with revised lighting regulations. It is easy to confuse later Series IIa models with the Series III, though nothing was changed on these vehicles other than the location of the headlamps. The Series IIA Lightweight was replaced by the Series III Lightweight in 1972, soon after the replacement of the civilian Series IIA with the Series III. The vehicle remained in essence the same, with a few relatively minor changes – there are detail differences to the chassis; and a revised gearbox had synchromesh on second through fourth gears instead of just third and fourth. In the electrical department the Series III was fitted with an alternator in place of the dynamo of the Series IIa; the new indicator switch incorporates a headlamp flasher and horn; and the ignition switch was now fitted in a new steering column cowl instead of on the dashboard. The Lightweight did retain the earlier Series IIa metal dashboard even after the upgrade. Around 1980, in line with civilian models, the engine had five main bearings instead of three. Lightweight production ended in 1984, when the parent Land Rover Series III was replaced by the models 90 and 110. A total of 37,897 Lightweights, petrols and diesels, were built

MERCEDES-BENZ

The SLS was the first Mercedes-Benz designed and built from scratch entirely by AMG. Upon its introduction at the 2009 Frankfurt Motor Show, the SLS AMG’s 571 PS (563 bhp) M159 engine was according to AMG “the world’s most powerful naturally aspirated production series engine” ever produced. The SLS AMG was designed by Mark Fetherston to be a modern 300SL Gullwing, adopting the feature of the gull-wing doors that swing open upwards on gas struts, and must be closed manually as AMG engineers decided against the 41 kg (90 lb) of additional weight that auto-closing systems would have added to the car. In case of a roll-over, the doors can be fully detached to allow the occupants to leave the vehicle. The SLS AMG Roadster was unveiled at the 2011 Frankfurt International Motor Show, as convertible variant, with conventional doors and three-layered fabric soft top (having a magnesium, steel and aluminium construction) which opens and closes in 11 seconds, and can be operated on the move at up to 50 km/h (31 mph). The roadster’s DIN kerb weight is 40 kg (88 lb) more than the SLS AMG Coupé. Certain reinforcements were made to the roadster in order to compensate for the loss of roof which includes side skirts with greater wall thicknesses and more chambers, a dashboard cross-member is supported against the windscreen frame and centre tunnel by additional struts, a curved strut between the soft top and the tank reinforces the rear axle, a reinforcing cross-member behind the seats to support the fixed roll-over protection system. An electric version of the car, the SLS AMG Electric Drive, was presented at the 2012 Paris Motor Show, but never entered production. The more focused Black Series, with more power and reduced weight did, though, following a presentation at the 2012 Los Angeles Show. Plenty of special editions of the car did, though, culminating in the 2014 SLS AMG GT Final Edition. The SLS was replaced by the somewhat cheaper (to build and hence to buy) AMG GT which remains in production.

NICHOLS CARS

Attracting lots of interest was this, the Nichols Cars N1A. If you were looking to buy a killer road-legal track car from a small company you’d never heard of it’d be reassuring to know that the man who designed it knew what he was doing. Rest assured, Nichols Cars has that covered. CEO Steve Nichols is credited as the guy who introduced carbon fibre to Formula 1 and was the lead designer on the MP4/4 that Ayrton Senna used in 1988 to score the first of three F1 Drivers Championships. He also worked on F1 programs for Ferrari, Jaguar, Jordan, and Sauber. That’s a pretty solid CV and Nichols has drawn on some of that technical experience for his first car, though the inspiration comes from much further back in McLaren’s past. In both style and name, Nichols’ N1A pays homage to McLaren’s M1A, the closed-wheel racer built between 1963 and 1968. The M1A raced in the hardcore Group 7 class in Europe in the mid-1960s as well as the United States Road Racing Championships in North America, where it evolved into the M1B and M1C for Can-Am competition. The modern N1A’s slippery bodywork is undeniably similar but is fashioned from carbon fibre and is both wider and longer. It also rolls on much bigger 19-in-front and 20-in rear wheels wrapped in modern Michelin Pilot Sport Cup 2 rubber, while the aluminium chassis features double wishbones all around, plus standard traction control, and can be optioned with power steering and anti-lock brakes. But the heart of the N1A is the 7.0-liter LS V8 located behind the rear seats and driving the rear wheels through a six-speed manual transmission with a classic open-gate shifter. Original M1As made between 310 and 550 hp (314-558 PS) but this one is modified to create rather more by Langford Performance Engineering, whose boss, Richard Langford, was one of the crew behind the Cosworth DFV that dominated F1 for years. The result is 650 hp (659 PS), which ought to be plenty given the sub-1000 kg ( 2,200 lb) curb weight. Nichols plans to build no more than 100 cars, and that includes 15 – one for each of the McLaren MP4/4’s victories – fully loaded launch edition cars with the 7.0-liter V8. Customers looking to save money can outfit the regular production cars with a 460 hp (466 PS) Chevy LT1 or 520 hp (527 PS) version featuring throttle bodies.

PORSCHE

Nice to see another 914 here as these cars are quite rare in the UK

There was also a 911 RS Carrera.

RENAULT-ALPINE

This rather nice original A110 Renault-Alpine model caught my eye. The A110 was introduced as an evolution of the A108. Like other road-going Alpines, the 1961 A110 used many Renault parts – including engines. But while the preceding A108 was designed around Dauphine components, the A110 was updated to use R8 parts. Unlike the A108, which was available first as a cabriolet and only later as a coupé, the A110 was delivered first with “Berlinetta” bodywork and then as a cabriolet. The main visible difference with the A108 coupé was a restyling of the rear body to fit the larger engine, which gave the car a more aggressive look. Like the A108, the A110 featured a steel backbone chassis with fibreglass body. The A110 was originally available with 1.1 litre R8 Major or R8 Gordini engines. The Gordini engine delivered 95 hp at 6,500 rpm. The A110 achieved most of its fame in the early 1970s as a victorious rally car. After winning several rallies in France in the late 1960s with iron-cast R8 Gordini engines the car was fitted with the aluminium-block Renault 16 TS engine. With two dual-chamber Weber 45 carburettors, the TS engine delivered 125 hp at 6,000 rpm. This allowed the production 1600S to reach a top speed of 210 km/h (130 mph). The longer wheelbase 2+2 Alpine GT4, originally considered a version of the A108, was updated with A110 engines and mechanicals, now being marketed as the “A110 GT4”. The car reached international fame during the 1970–1972 seasons when it participated in the newly created International Championship for Manufacturers, winning several events around Europe and being considered one of the strongest rally cars of its time. Notable performances from the car included victory in the 1971 Monte Carlo Rally with Swedish driver Ove Andersson. With the buy-out of Alpine by Renault complete, the International Championship was replaced by the World Rally Championship for 1973, at which time Renault elected to compete with the A110. With a team featuring Bernard Darniche, Jean-Pierre Nicolas and Jean-Luc Thérier as permanent drivers and “guest stars” like Jean-Claude Andruet (who won the 1973 Monte Carlo Rally) the A110 won most races where the works team was entered, making Alpine the first World Rally Champion. Later competition-spec A110s received engines of up to 1.8 litres. As well as being built at Alpine’s Dieppe factory, A110 models were constructed by various other vehicle manufacturers around the world. The Alpine A110 was produced in Mexico under the name “Dinalpin”, from 1965 to 1974, by Diesel Nacional (DINA), which also produced Renault vehicles. The Alpine A110 was also produced in Bulgaria under the name “Bulgaralpine”, from 1967 to 1969, by a cooperative formed between SPC Metalhim and ETO Bulet, whose collaboration also resulted in the production of the Bulgarrenault. In 1974 the mid-engined Lancia Stratos, the first car designed from scratch for rally racing, was operational and homologated. At the same time, it was obvious that the tail-engined A110 had begun reaching the end of its development. The adoption of fuel injection brought no performance increase. On some cars, a DOHC 16-valve head was fitted to the engine, but it proved unreliable. Chassis modification, like the use of an A310 double wishbone rear suspension, homologated with the A110 1600SC, also failed to increase performance. On the international stage, the Stratos proved to be the “ultimate weapon”, making the A110, as well as many other rally cars, soon obsolete. The A110 is still seen in events such as the Rallye Monte-Carlo Historique and there was a nice example here.

ROVER

Once the object of desire as an executive car, the P6 Rover now ranks for its classic appeal.

SUBARU

This is a P1 version of the first generation Impreza. To counter the grey imports of high-performance Japanese variants, Subaru UK commissioned Prodrive to produce a limited edition of 1,000 two-door cars in Sonic Blue, called the WRX “P1”. Released in March 2000, they were taken from the STI Type R lines and used for the P1. The car was the only coupé version of the WRX STI GC chassis to receive ABS. In order to allow for ABS, the DCCD was dropped. Engine output was boosted to 276 bhp, and the suspension optimised for British roads. Options were available from Subaru consisting of four-piston front brake calipers, electric Recaro seats, 18-inch wheels and a P1 stamped backbox. The P1, or Prodrive One, is echoed in the name of the Prodrive P2 concept car. They are among the most sought after of all Subaru Impreza models now.

VAUXHALL

The VX220 is the only true sports car that the marque has produced in the last 90 years. Quite unlike any Vauxhall that had ever come before it, the VX220 was the result of a deal between GM and Lotus, struck to generate enough funding for the latter to be able to develop a replacement for their Elise model, something forced on them owing to changes in European crash safety regulations for the 2000 model year. Lotus agreed to develop and produce a 2 seater sports car for GM, on the new Series 2 Elise chassis, with a concept version of the proposed GM model being shown at the Geneva Motor Show in 1999. Although the body styling was different, clearly the economies would only work if as much else could be shared, and that presented a challenge as it was planned to use a 1.8-litre Toyota engine, similar to that found in the Toyota Celica, in the second generation Elise, whereas the GM cars clearly had to use a GM engine, namely the  2.2-litre GM Ecotec engine from the Astra. As neither engine had been used in the original Elise, which had been fitted with a 1.8-litre Rover K-Series engine, this simply became one of the many design challenges .In order to accommodate the production of the new cars, Lotus expanded its Hethel factory to a capacity of 10,000 cars, with around 3,500 slots allocated to Speedster production. Production of the Speedster commenced in 2000. The car was hailed by the motoring press as a great drivers’ car and won several accolades, including Top Gear’s Car of the Year in 2003. The lesser naturally aspirated 2.2 version was considered easier to drive than the potent Turbo model, and some journalists suggested that the Opel/Vauxhall car was better value for money than the Lotus, among them one Jeremy Clarkson in his 2003 DVD Shoot Out. However, the market did not really agree, and sales were limited. The car was deleted in 2005, with no successor.

DRAG CARS

One of the displays to the side, and quite likely missed by many, unless you were in earshot and went to investigate were a series drag cars.

RALLY CARS

Co-located with the drag cars was a nice display of legendary classic rally cars.

TRADE STANDS and OTHER ATTRACTIONS

As well as the Foodie stuff, which occupied a lot of space but which did not seem to have much in it, there were plenty of other attractions and activities across the site, including the large Trade Stand area. There was live music on all three evenings from chart-topping bands including The Christians, ABC, the Sugababes and McFly.  We stayed one evening, as did a lot of other people, but were disappointed that all the food stands had either run out of food or closed, so we left rather hungry! There was even a pop-up Diddly Squat Farm Shop with an adjoining bar selling Jeremy Clarkson’s own Hawkstone beers and ciders.

FERGUSON

Harry Ferguson built his first tractor in Belfast in 1933, but it was not until 1946 when mass production began, after Ferguson entered an agreement with the Standard Motor Company, to use their factory on Banner Lane. The little grey TE20 tractors were a sensation when new, and are much prized now.

FORD

Now rare are examples of the first generation Transit which was introduced in October 1965, taking over directly from the Thames 400E. This generation had the longest production run of any Transit to date, staying largely unaltered for 12 years until the major facelift of 1978, with overall production lasting for over 20 years before finally being replaced by the all-new VE6 platform in 1986. The van was produced initially at Ford’s Langley facility in Berkshire, England (a former Second World War aircraft factory which had produced Hawker Hurricane fighters), but demand outstripped the capability of the plant, and production was moved to Southampton until closure in 2013 in favour of the Turkish factory. Transits were also produced in Ford’s Genk factory in Belgium and also Turkey. Transits were produced in Amsterdam for the local market from the mid-1970s until the end of 1981. This factory had ample capacity, since the Ford Transcontinental produced there had little success (total production 8000 in 6 years). Although the Transit sold well in the Netherlands, it was not enough to save the factory, which closed in December 1981. The Transit was introduced to replace the Ford Thames 400E, a small mid-engined forward control van noted for its narrow track which was in competition with similar-looking but larger vehicles from the BMC J4 and J2 vans and Rootes Group’s Commer PB ranges. In a UK market segment then dominated by the Bedford CA, Ford’s Thames competitor, because of its restricted load area, failed to attract fleet users in sufficient numbers. Ford switched to a front-engined configuration, as did the 1950s by Bedford with their well-regarded CA series vans. Henry Ford II’s revolutionary step was to combine the engineering efforts of Ford of Britain and Ford of Germany to create a prototype for the Ford of Europe of today—previously the two subsidiaries had avoided competing in one another’s domestic markets but had been direct competitors in other European markets. The Transit was a departure from the European commercial vehicles of the day with its American-inspired styling—its broad track gave it a huge advantage in carrying capacity over comparable vehicles of the day. Most of the Transit’s mechanical components were adapted from Ford’s car range of the time. Another key to the Transit’s success was the sheer number of different body styles: panel vans in long and short wheelbase forms, pick-up truck, minibuses, crew-cabs to name but a few. The engines used in the UK were the Essex V4 for the petrol-engined version in 1.7 litre and 2.0 litre capacities. By using relatively short V-4 engines Ford were able to minimise the additional length necessitated to place the engine ahead of the driver. Another popular development under the bonnet was the equipping of the van with an alternator at time when the UK market competitors expected buyers to be content with a dynamo. A 43 bhp diesel engine sourced from Perkins was also offered. As this engine was too long to fit under the Transit’s stubby nose, the diesel version featured a longer bonnet – which became nicknamed as the “pig snout”. The underpowered Perkins proved unpopular, and was replaced by Ford’s own York unit in 1972. For mainland Europe the Transit had the German Ford Taunus V4 engine in Cologne 1.3, 1.5, and 1.7- or Essex 2.0-litre versions. The diesel version’s long nose front was also used to accommodate the Ford 3.0 litre Ford Essex V6 engine (UK) for high performance applications such as vans supplied to police and ambulance services. In Australia, in 1973, to supplement the two Essex V4 engines that were available the Transit was released with the long-nose diesel front used to accommodate an inline 6-cylinder engine derived from the Ford Falcon. The Metropolitan Police reported on this vehicle in 1972 via a Scotland Yard spokesman that ‘Ford Transits are used in 95 per cent of bank raids. With the performance of a car, and space for 1.75 tonnes of loot, the Transit is proving to be the perfect getaway vehicle…’, describing it as ‘Britain’s most wanted van’. The adoption of a front beam axle in place of a system incorporating independent front suspension that had featured on its UK predecessor might have been seen as a backward step by some, but on the road commentators felt that the Transit’s wider track and longer wheelbase more than compensated for the apparent step backwards represented by Ford’s suspension choices. Drivers appreciated the elimination of the excessive noise, smell and cabin heat that resulted from placing the driver above or adjacent to the engine compartment in the Thames 400E and other forward control light vans of the 1950s and early 1960s. The Transit was also assembled in South Africa between 1967 and 1974, the last Transit to be sold in that country until 2013, when a fully imported model was introduced. A facelifted version was introduced in 1977 and would continue until early 1986 when an all-new model was introduced.

RENAULT

With the MOTUL stand, I found this rather nice Renault Gallion. The Renault 2,500 kg (or 2T5) and the Renault Galion were truck/vans with a 2.5-tonne carrying capacity manufactured by Renault between 1947 and 1957 and then by its subsidiary Saviem between 1957 and 1965. In 1947, Renault launched the Renault 2,500 kg light truck to replace the AHx series. The new vehicle was produced at Renault’s main plant in Boulougne-Billancourt. In 1957, the company moved the production of some of its small commercial vehicle range to Saviem’s Blainville-sur-Orne plant, which was built on the former site of the Cahen shipyards. They were the Goélette (loading capacity of up to 1.4 tonnes) and the Renault 2 T 5, renamed Galion (keeping loading capacity of up to 2.5 tonnes). The new models continued being marketed as Renault. The Galion and Goélette names were officially introduced in 1959, prior to that they were still sold with the previous 1T4 and 2T5 denominations. By 1961, Saviem was producing between 50 and 60 Galions per day. At the time they were offered with at least two inline-four engines: the 3-litre diesel 4 192 supplied by Perkins, with a maximum power output of 52 bhp at 2,400 rpm and a 2-litre petrol Renault unit with a maximum power output of 56 bhp at 3,300 rpm. The truck had a rear-wheel drive transmission through a universal joint, coupled to a 4-speed manual gearbox. The Galion mounted various petrol engines. Some versions used the 668-8 with a maximum power output of 52 bhp at 3,300 rpm and a torque of 126 Nm; or 93 lb/ft at 2,000. Other Galion versions used the 2.1-litre 671-2 Étendard. The 671-2 had a power output of 55 bhp at 3,300 rpm and a torque of 140 Nm or 103 lb/ft) at 2,000 rpm. At the 1962 Paris Motor Show, Renault announced a new diesel engine for the Galion, replacing the Perkins unit. The new engine, called 580, was a 2.72-litre four-cylinder unit and had a power output of 58 bhp  at 2,900 rpm. In 1965, following various revisions to the Galion design, Saviem introduced the more modern and powerful Saviem Super Galion range, and the Galion was discontinued.

TIPO 184

This is called the Tipo 184, and it’s actually a dinky Mazda MX-5 in Forties period costume. It’s the work of Ant Anstead and the team at Dowsett Cars who wanted to offer an affordable and approachable project build for the average driver. For around £20k (plus a donor Mk2 MX-5) you can buy the kit and build one of these yourself in a week or two, depending on mechanical competence. That’s a lot of historic race car, for not a crippling amount of money. It’ll swallow 100 to 150 hours of your life building one, so we’re told. Worry not, for you can order the kit in smaller, cheaper stages – a bit like those ‘make your own Starship Enterprise!’ magazine series that pop up every January, only with a less surprising final bill for this actual, functioning motor vehicle. Namely £17,700 plus VAT and a forlorn drop-top Mazda. Finish your Tipo 184 imminently and it’ll be limited to track, but a road car conversion kit is coming soon. Which if you’re spending 20 big ones on a car with the modest power output of a two-decade-old roadster, we’d suggest is pretty key to unlocking some of its appeal. Mind with just one seat and no luggage space – plus the need to wear some decent face protection if you aren’t to be pinged mercilessly by stones – it’ll be a road car with a limited-use case. A one-make race series will launch in the UK and USA in 2022, for which you’ll need to ensure your MX-5 is (deep breath) a five-speed manual, 1.8-litre MX-5 or Miata NB produced between 1998 and 2001. The engine’s from an MX-5, so it’s a non-turbo four-cylinder of deliberately modest power. Namely 146bhp (at 7,000rpm) and 124lb ft of torque (at 5,000rpm). But shorn of any roof, doors and most of the MX-5’s other already meagre creature comforts, the Tipo 184 is over 300kg lighter, at 700kg, its mass split 55/45 front/rear. And, somewhat vitally, the driver’s height limit is 6 foot 3. The MX-5’s engine, gearbox, propshaft, diff, braking system (including handbrake cable), suspension and steering rack all remain, the latter with its power assistance removed. The instrument pod also hangs around, and once you’ve navigated your way into the 184 – cagily climbing its exterior componentry like it’s a Total Wipeout obstacle – those are the first things you’ll spot. Their slightly naff, italicised fonts don’t entirely fit the 1940s F1 car vibe, but what’s reassuring about them is the oil and water temperatures don’t really budge when you’re working the car hard. It’s difficult to imagine the Alfa Romeo 158 Alfetta Grand Prix car it pays homage to being able to claim similar, but you’ve sturdy 1990s mechanicals to thank for that.

COMPETITOR PARKING

A vast area which stretches from opposite the International Pits almost all the way back to the rest of the event is allocated for the usage of competitors and their support teams for their motorhomes and other vehicles. It is always worth wandering among this, as there tend to be some interesting and often rare cars just tucked up among them, so we did just that.

The motorhomes are vast, and most of the ones you see are very recent machines with all the latest luxury features, but there are some older ones, too, and this amazing Airstream type vehicle certainly caught our eye.

ALFA ROMEO

No surprise to see an enthusiast car like the Giulia among the many parked among the motor homes. On 2 March 2020, Alfa Romeo introduced two new GTA and GTAm models which would have a limited production run of 500 units. The GTA and GTAm versions are developed to celebrate the marque’s 110th anniversary in 2020, and pay tribute to one of the most emblematic automobile of Alfa Romeo: Giulia GTA. The GTA and GTAm use the same engine, rated at 540 PS/533 bhp and are 100 kilograms (220 lb) lighter than the Quadrifoglio, allowing for a power to weight ratio of 2.82 kg/PS. The GTA and GTAm can accelerate from 0 to 100 km/h in 3.6 seconds, with launch control. The GTAm is a track focused model and as a result has two seats, racing harnesses, and Lexan side and rear windows. The GTA’s handling was improved by widening the front and rear track by 50 millimetres (2.0 in). The car is fitted with single nut wheels for weight reduction measures. Broader fenders cover the additional width. New springs, shocks, and bushings update the suspension as further means to improve the handling. Buyers will also receive a “personalized experience package” which includes a Bell racing helmet in special GTA livery, a full racing suit by Alpinestars, a personalized Goodwool car cover, and a specific driving course devised by the Alfa Romeo Driving Academy. Modifications to the engine include higher boost pressure from the turbochargers, an Akrapovič exhaust system and redesigned pistons to ensure constant power and reliability: the piston cooling system now uses four oil jets instead of two as is the case on the Quadrifoglio model.

ASTON MARTIN

Most special of the Aston Martins we spotted was this V600. As with many other Aston Martin models, a high-performance Vantage model of the Virage would later be introduced. First shown at Birmingham in September 1992, the Vantage was produced from 1993 through 2000 and, like many other Aston Vantage models would soon become the only variant available. The Virage name lasted just a few years, with its final descendants inheriting the simple and familiar V8 name. The Vantage had new styling with only the roof, doors and wing mirrors shared with the Virage. The wing mirrors were later replaced in favour of the ones from the Jaguar XK8/XKR. The Vantage is wider, lower, used four round tail lights (later adopted for the base V8 Coupe), and featured new rear suspension and interior electronics. Like the 6.3, the Vantage used record-sized 362 mm (14 in) brake discs and 18 inch wheels. The biggest change to the Vantage was inside the engine compartment. The 5.3 L (5,341 cc) V8 engine now used twin superchargers. Power output was now 550 bhp, and the torque was equally high at 555 lb/ft (752 Nm) at 4,000 rpm. Top speed was 300 km/h (186 mph), with acceleration to 60 mph taking 4.6 seconds.Customers cars could be returned to Works Service starting in 1998 to be converted to V600 specifications, where the engine was upgraded to 600 bhp at 6,200 rpm and 600 lb/ft (813 Nm) of torque at 4,400 rpm. In 2000, Aston Martin’s Works Service unit also built nine bespoke Vantage Volante models (convertibles), one of which was built to long wheelbase

There was also a very bright blue of the previous generation Vantage and an example of the current model.

CITROEN

The C4 by Loeb (wouldn’t ‘Loeb edition’ have sounded much less pretentious?) is a limited-edition C4 built to honour Sebastian Loeb’s achievements in world rallying and Citröen’s return to the WRC championship after a short break. As for the great man’s involvement in the programme, it’d be nice to think that he toiled away for hours sorting out the damper settings and fighting with the engineers on our behalf for a proper hydraulic steering system. But what he probably did was get a bung in exchange for the use of his name. So what sets it apart from your common or garden C4 VTS? Available only in either red or black, the C4 gets 17-inch rims in either white or grey, ‘By Loeb’ badging and an individual serial number to denote which of the 400 cars coming to the UK is yours. Inside, a mix of black and red leather and cloth brightens up the interior, there are Citröen chevrons embroidered onto the headrests and smatterings of chrome and aluminium on the dash and the pedals. Other than that, it’s stock C4.

FERRARI

Among the Ferrari models here were the F12 Berlinetta and its replacement, the 812 Superfast as well as the recently available 296 GTB

FORD

A common sight in the US, the Explorer is little known over here. This is the previous generation model.

HONDA

The latest Civic Type R is still not a very common sight on our roads, so it was nice to see one here.

LAND ROVER

This customised version of the latest Range Rover caught our attention as we walked by.

MERCEDES-BENZ

Nice to see another example of the W111 generation coupe model from the 1960s here.

Rather more recent was this example of the current sports car, the AMG GT.

PORSCHE

The 911 has always been an enthusiast car, so you could reasonably expect to see a number of them in this area, and sure enough, there were, from an early 70s car right to the latest 922-generation GT3 Touring.

ROLLS ROYCE

Whoever came in the vast Cullinan would certainly have arrived in luxury, even if “style” is rather more questionable.

IN THE PADDOCKS

With so much else going on and to see, it is easy to lose sight of the fact that at its core, this is a classic motor racing event. And this year was rather special as it marks 75 years of the Silverstone circuit, so in partnership with Masters Historic Racing, HSCC, HGPCA and Masters Racing Legends there was a bumper timetable throughout the weekend, with grids seemingly offering more depth and diversity than has been seen over the past couple of editions, certainly a fine way to celebrate this landmark year in the history of Silverstone. The HGPCA in particular, holding the 75th Anniversary Trophy for front engine Grand Prix cars from 1948-1960, harking back to the very start of Silverstone’s racing history, with a field featuring imperious cars such as the Maserati 250F, Ferrari 246 Dino and Talbot Lago T26 to name but a few. There were no fewer than 20 memorable showdowns of the very best and closes retro racing staged over the weekend. Friday was practice day with racing on the Saturday and Sunday. Several of the races had packed grids with over 50 cars and the scope covered cars from all genres you can think of from the last 100 years, with more modern machinery to be seen in action here than has been the case in the past.

In total there were over 900 cars competing over the 3 days, both pit complexes are in use throughout. There is pretty much unrestricted access, so you can wander freely not just among the paddocks but also into the pit garages. Whilst the national pits (the old ones) are easily accessible, the international pits are further away. Although you can walk there, most people prefer to take one of the shuttle buses which trundle back and forth from the centre of the circuit all day. There did not seem to be quite such long queues as I had encountered in previous years, but even so, you do need to allocate quite a bit of time for the trip down there, to have a look and to get back. I went down a couple of times over the weekend, and there was plenty to see, as expected. Whilst some cars will be present throughout the entire event, you do need to remember that for the classes whose final race is on the Saturday, many of the teams will pack up and leave the site, so if you wait until Sunday – as I have done some times in the past – you will miss seeing some of the cars altogether.

Getting about the site is something that the competitors and their support teams have to do, too, and they us all manner of ways of doing this, from bikes of the traditional and electric types, as well as various other vehicles. A number of these caught our eye.

Ferves Ranger: First seen at the 1966 Turin Motor Show, Ferves (FERrari VEicoli Speciali) introduced the Ranger as a small off-road derivative of the Fiat 500 and Fiat 600. The car had an open body with 4 vinyl-covered seats, a folding windscreen, and removable suicide doors on early models, later models had normally hinged doors. It was powered by a rear-mounted 499 cc two-cylinder in-line engine from the Fiat 500 and was available as a two-wheel drive or four wheel drive and had a maximum speed of around 45 mph. There was also a cargo version with a carrying capacity of 300 kg. The engine and steering were from the Fiat 500 and the suspension and brakes from the Fiat 600. The chassis numbers commenced at 300 for the passenger version and 100 for the cargo. Around 600 were built, all of them with Left Hand Drive and around 50 are thought to survive.

Mazda B1800 pickup

Mini Moke

Much larger than these were this duo: An Audi Q7 is not particularly rare, but this was the V12 engined version and that is not a common sighting, and there was also the massive RAM 1500 here.

Some of the support vans here were rather special, too, such as this Ford Econoline. Ford released the first-generation Ford Econoline on September 21, 1960, for the 1961 model year. Beginning development in 1957, the model line served as a replacement for the Ford F-Series panel delivery (and the smaller Ford Courier sedan delivery). Three models were available, a cargo van, a passenger van (also sold under the Station Bus and Club Wagon names), and a forward-control pickup truck. Competing directly against the rear-engined Chevrolet Corvair van and Volkswagen Transporter, the Ford Econoline established multiple design precedents adopted by successive North American vans, including the Chevrolet Van and Dodge A100. While also a forward-control vehicle, Ford introduced a midengined configuration. To improve cargo access by creating a flat load floor and enlarging the rear doors, the engine was placed between the front seats. The first-generation Ford Econoline was based on the Ford Falcon compact car range. To accommodate its 90-inch wheelbase (the shortest for a Ford since 1908), the Econoline adopted a midengined configuration, placing the engine behind the front axle; consequently, the layout precluded the use of a V8 engine. The Econoline was initially powered by the 85 hp 144-cubic-inch inline-six (the standard engine of the Falcon); a 101 hp 170-cubic-inch inline-six was introduced as an option. For 1965, the 170 six became standard, with a 240 cubic-inch six introduced as an option. A three-speed manual was standard, with a Dagenham four-speed manual introduced for 1963 and discontinued in 1964; the 170-cubic-inch engine was offered with a three-speed automatic in 1964, and the larger two engines were both offered with a three-speed automatic as an option thereafter. In contrast to the Falcon, the Econoline was fitted with a solid front axle and a solid rear axle suspension with leaf springs for all four wheels. In its body design, the Ford Econoline adapted several elements of the Volkswagen Type 2, while making major departures with other design features to accommodate its mid-engined layout. In line with Volkswagen, the Econoline positioned the front seats above the front axle, making it a cabover-style configuration (similar to the Jeep Forward Control). The grille placed below the headlights was a design feature borrowed loosely from the Ford Thames 400E (a predecessor of the Ford Transit). The midengined placement enlarged the cargo area, as the engine compartment was located forward of the flat load floor. While Volkswagen marketed rear-engined vans in the United States until 1991, Chevrolet/GMC and Dodge both adopted the design of the Econoline, introducing midengined vans for the 1964 model year. Through its production, the first-generation Ford Econoline was offered in several variants. Alongside the standard six-door cargo van, an eight-door version (adding two doors on the driver side) was added for 1963. For 1964, a panel van was introduced, deleting side loading doors altogether. For 1965, a “Super Van” extended-length body was introduced, extending the body 18 inches behind the rear axle. Econoline cargo vans (except panel vans) were offered with or without side windows in several configurations.

Rather larger is this 1947 Diamond T 509 Truck. For more than 50 years, Diamond T built straight trucks and semis for serious hauling jobs. The company also soldiered through two World Wars and manufactured heavy rigs that the Allies used to move supplies and matériel. Diamond T’s last call as an independent badge came in 1966 after which it was consolidated with Reo to form the Diamond Reo division of White in the spring of 1967. Diamond Reo changed hands, struggled through bankruptcy in the 1970s, and changed hands again. It lives on today through a Pennsylvania-based truck builder as the T-Line brand of custom trucks and glider kits. This is a 1947 Model 509 Diamond T–the company’s midsize offering that year with a 14,700-pound gross vehicle weight. It was built during the postwar boom when demand for trucks was at an all-time high. In 1947, Diamond T manufactured 10,475 trucks, then climbed to a record output in ’48 with 10,651. The truck maker’s story begins in the early 1900s when C.A. Tilt, the son of a Chicago shoe manufacturer built a car of his own design, working out of the machine shop in the family’s factory. The Diamond T name and logo was co-opted from his father’s shoes–the diamond was meant to represent high-quality while the “T” in the centre stood for Tilt. After building cars for about five years, a Chicago plumbing supply business ordered a delivery truck from Tilt in 1911, and Diamond T trucks was born. That first 11/2-ton chain-drive hauler paved the way for a dealer network and a new heavy-truck factory in Chicago by 1917. From the start, Diamond T’s were built almost entirely using components supplied by outside vendors–a common practice in heavy-truck manufacturing that continued for more than a century. Diamond T’s new plant also went immediately to work building the World War I Standard B Liberty military truck: a single-axle, two-wheel-drive, heavy hauler designed by the U.S. Quartermaster Corps and manufactured by 15 different companies. In the early 1920s, Diamond T offered an expanded line of trucks ranging from two to five tons. By the end of the decade, the company’s lineup had advanced dramatically: four-cylinder engines were replaced by sixes; four-speed transmissions replaced earlier three speeds; its trucks were using hydraulic brakes and rolling on heavy steel wheels shod with pneumatic tires; tandem rear axles were offered; and the range grew to include one-ton trucks all the way up to 12-ton rigs. In addition to piling on advanced features, the company was beginning to heap on chrome trim to further accentuate the trucks’ styling, which began its long lasting reputation for building fancy commercial rigs. A makeover in 1933 ushered in new cabs with slanted V-shaped windshields and a bold grille with vertical slats. The styling became even more aggressive in 1936 when the windshield was tipped back dramatically and the cab squared off at the corners. That year also saw the debut of the Diamond T Model 80 3/4-ton light truck, of which only a handful were built until it was discontinued in 1938 and replaced by the more robust Model 201. While the 1938 cab stuck around until 1951, the grille underwent some styling changes leading up to WWII. The new-for-1940 treatment became a sort of trademark for the company, with its fat horizontal grille bars that would influence the design of Diamond T front ends into the 1960s.  The Diamond T is powered by its original Hercules 282-cu.in. straight-six, rated at 99 horsepower, and it breathes through its factory one-barrel Zenith carburettor. A non-synchromesh Warner T-9 four-speed and a vacuum-operated two-speed rear was installed in the truck on the Diamond T assembly line to give the operator a wider selection of ratios.

Most of the cars in the paddocks were competing, or were support vehicles, but there were a few special display vehicles as well. My eye was taken by a rather nice “Derby” Bentley from the late 1930s and on show near it was a slightly earlier Frazer Nash.

This is the Lotus-Radford Type 62-2 or simply Radford Type 62-2 is a sports car produced by British coachbuilding firm Harold Radford in partnership with Lotus Cars. Built as a homage to the original Lotus 62, production will be limited to 62 units. The car is available in three trim levels: “Classic”, “Gold Leaf”, and “John Player Special”. Of the 62 planned units, twelve will be in the John Player Special trim, and another twelve will be in the Gold Leaf trim. Based on the Lotus Exige, the Type 62-2 shares the chassis and engine, the former of which also has a new rear subframe. Harold Radford is a British coachbuilding firm founded in 1948 in Kensington which started off by restyling numerous Bentleys and Rolls-Royces, producing cars such as the 1951 Bentley Countryman. The firm engaged in other endeavours such as building the fibreglass bodywork for the first Ford GT40 prototype, shooting brake conversions for Aston Martin DB5s, and customising Minis. Defunct after the 1960s, Formula One drivers’ champion Jenson Button alongside designer Mark Stubbs, Ant Anstead, and lawyer Roger Behle revived the Radford marque in 2021, with the Type 62-2 being the company’s first wholly in-house design. Radford also purchased the rights to use the John Player Special livery used on several Lotus Formula One cars in the 1970s. With the three trim levels come two different liveries: the Gold Leaf wears the same livery that appeared on the original Lotus 62, and the John Player Special trim is a tribute to the eponymous Formula One livery that the Lotus Formula One team bore in the 1970s. The Classic is the most aerodynamically basic trim, the Gold Leaf trim receives two small wickerbills at the rear of the car, and the John Player Special is the most aerodynamically advanced trim, with a larger front splitter and rear diffuser, combined with larger side intakes to help cool the engine. Radford, being a coachbuilding company, has also given customers the option of fitting features such as a wickerbill on trims that would not otherwise have them. Radford also offers a “Quali Edition” package on top of the Gold Leaf trim, which offers more aggressive aerodynamic features such as a larger front splitter and rear diffuser, carbon ceramic brakes, and carbon composite wheels. The Lotus badge on the front is also gold set against enamel. Significant use of carbon composites in the body panels alongside lightweight bonded and riveted aluminium bring the dry weight of the 62-2 to just under 1,000 kg (2,205 lb). The interior of the Type 62-2 is largely analogue; the dashboard is outfitted with a stopwatch and an analog clock in partnership with British watchmaker Bremont, various toggle switches also adorn it, and the steering wheel is devoid of any buttons. Digital connectivity is still provided by a build plaque (which contains the vehicle identifier unique to every chassis), which doubles as a magnetic phone holder/wireless charger, along with Wi-Fi and Bluetooth capabilities. Although the Type 62-2 was designed for trackability, there is still room for luggage behind the engine bay, albeit not much. The 62-2 borrows the Toyota 2GR-FE from the Exige, producing 436 PS in the Classic trim and 507 PS in the Gold Leaf trim via an ECU remap. The John Player Special and Gold Leaf trims receive upgraded camshafts, pistons, and connecting rods, with the former also receiving a larger supercharger. The enlarged supercharger gives the John Player Special trim an output of 608 PS. The Classic is the sole trim level available with a six-speed manual transmission, the Gold Leaf and John Player Special trims both come with a seven-speed dual-clutch transmission and a limited-slip differential. However, Radford still offers customisability and the option for Classic trim owners to upgrade to the dual-clutch transmission and more powerful Gold Leaf engine. Traction control and an anti-lock braking system are available with the dual-clutch transmission and can be turned off at the driver’s discretion. Coilover springs provide the Type 62-2’s ride height control, with all four dampers being individually adjustable, along with a nose lift option to negotiate raised surfaces such as speed bumps. The Classic trim comes with 17-inch wheels at the front and 18-inch wheels at the rear, with the Gold Leaf and John Player Special trims receiving 18-inch front and 19-inch rear wheels by Dymag. The John Player Special also has the option of carbon fibre wheels like the Quali Edition package for the Gold Leaf, along with Michelin Pilot Sport Cup 2 tyres. It also receives AP calipers and 360 mm (14.2 in) carbon ceramic rotors. The Gold Leaf and Classic trims come with 4-piston AP calipers and iron rotors.

The McMurtry Spéirling is an electric single-seat prototype sports car which was first presented at the Goodwood Festival of Speed in 2021. The car is developed by McMurtry Automotive, a British registered startup founded on 2 June 2016 by Sir David McMurtry (co-founder and executive chairman of Renishaw plc). “Spéirling” is Irish for “thunderstorm”. According to McMurtry, the motivation behind the car was to challenge the industry trend of increasingly heavier vehicles and, by using first principles design, create a lightweight electric drivers car. The prototype car is the first step to demonstrate what customers will experience on road and track. It is not currently in a racing series but is built to satisfy relevant motorsport safety requirements, with crash structures and a carbon-fibre monocoque chassis with integral rollover protection. Its unique performance differentiator is the fan powered downforce system, producing 2,000 kg (4,400 lb) of downforce at a standstill. The car was first presented at the Goodwood Festival of Speed on 8 July 2021, and driven by Derek Bell. The car had been developed in secrecy over three years. On 26 June 2022, the Spéirling achieved a new Goodwood Festival of Speed hill climb record, completing the 1.87-kilometre (1.16 mi) course in 39.08 seconds with McMurtry test driver Max Chilton behind the wheel.

The Tesla Roadster is a battery electric sports car, based on the Lotus Elise chassis, produced by Tesla Motors (now Tesla, Inc.) from 2008 to 2012. The Roadster was the first highway legal, serial production, all-electric car to use lithium-ion battery cells, and the first production all-electric car to travel more than 244 miles (393 km) per charge. It is also the first production car to be launched into deep space, carried by a Falcon Heavy rocket in a test flight on February 6, 2018. Tesla sold about 2,450 Roadsters in over 30 countries, and most of the last Roadsters were sold in Europe and Asia during the fourth quarter of 2012. Tesla produced right-hand-drive Roadsters from early 2010. The Roadster qualified for government incentives in several nations.

And so to the cars that were competing, of which just a subset are presented here:

HGCPA PRE-66 GRAND PRIX CARS

This would be a highlight for many, a special showdown for Grand Prix cars dating right back to the circuit’s opening in 1948. Starring a field of fabulous Ferraris, Maseratis, Cooper-Bristols and other period icons, there were three titles to be won, with an overall category for all pre-66 GP cars, as well as one for those that were front engine and another for rear-engined cars. The front-engined category was won by the 1960 Scarab Offenhauser of Mark Shaw and the rear-engined and overall winner was the Cooper T53 of Mark Bryant.

HSCC THUNDERSPORTS

The HSCC Thundersports showdown was won by Michael Lyons in the recently restored IBEC 308LM – the one-off Cosworth DFV engined sportscar designed by the legendary Harvey Postlethwaite to race at Le Mans in the late seventies.

MASTERS RACING LEGENDS FORMULA ONE 1966 – 1985

Some of the most mesmerizing and spellbinding moments of previous Silverstone Classic events have been provided by the special demonstrations that form an integral part of the on track action over the course of the weekend. There was no exception this year, with a superb demonstration of some of the loudest and dynamic Formula One cars to have graced the circuit in period to celebrate 75 years of action at Silverstone. The deafening roar of the Williams FW19, and screaming Dallara F191 rolled back the years as the grandstands reverberated to the sound of the now unthinkable V10 engines, while the gracious Mercedes F1 W04 in the hands of the supremely talented Esteban Gutierrez brought a more contemporary celebration. They were of course joined by a diverse grid of other Grand Prix greats, reaching back to the halcyon days of the 1970s, where cars like the sublime Tyrrell 001 wowed spectators with the raw blend of speed and innovation.

Lyons also triumphed in the second of the two blue-ribband showdowns for the Masters Racing Legends (Formula One ‘66-’85), this time behind the wheel of a JPS-liveried Lotus 92 as raced by Nigel Mansell in the 1983 F1 World Championship. The first was won by Florida-based Ken Tyrrell in his Tyrrell 011, the very car Michele Alboreto won the 1982 Caesar’s Palace Grand Prix to give the Cosworth DFV engine the last of its 155 Grands Prix victories.

ADRIAN FLUX TROPHY for TRANSALANTIC PRE 66 TOURING CARS

Another notable success came when multiple BTCC race winner Sam Tordoff roared back through the field of American muscle cars to take the chequered flag in the Adrian Flux Trophy for Transatlantic Pre ’66 Touring Cars – another 50+ car grid which included a number of touring car greats from yesteryear including Steve Soper, Gordon Sheddon and Andy Priaulx as well as Olympic cycling legend Sir Chris Hoy.

HSCC ROAD SPORTS TROPHY

MASTERS SPORTS CAR LEGENDS

Saturday’s standout highlights included Gary Pearson and Alex Brundle winning the Yokohama Trophy for Masters Sports Car Legends in one of two fantastic Ferrari 512Ms contesting the sunset showdown for Le Mans-style racers from between 1962-76.

MASTERS ENDURANCE RACING LEGENDS

Steve Brooks won the Masters Endurance Legends race in his stunning Peugeot 90X, a sister diesel-engined prototype to the Peugeot’s 2009 Le Mans victor. Brooks, though, was chased all the way by Tim de Silva in a Pescarolo LMP1, the hard-charging American setting a new 125.9mph lap record for the historic Silverstone circuit – a layout that features a slightly faster entry to Club Corner than used for the British Grand Prix and other races.

MASTERS RACING LEGENDS BIG CAT CHALLENGE

Sunday’s highlights included brothers John and Gary Pearson sharing a Jaguar E-type to win the 50-minute, two-driver MRL Big Cat Challenge – Gary adding to his trophy cabinet when also winning the MRL Stirling Moss Trophy in an earlier Jaguar D-type.

MASTERS GT TROPHY

INTERNATIONAL TROPHY FOR CLASSIC GT CARS

HISTORIC FORMULA JUNIOR

Setting the scene for action to follow, the packed racing programmes on both Saturday and Sunday kicked off with 50+ grids of jostling Formula Junior single-seaters. Both were edge-of-the-seat thrillers won by Sam Wilson in a Lotus 20/22 – Sunday’s victory came by just two hundredths of a second in a dramatic side-by-side photo finish with the Lotus 22 of Horatio Fitz-Simon.

MASTERS RACING LEGENDS RAC WOODCOTE TROPHY and STIRLING MOSS TROPHY

MASTERS RACING LEGENDS HISTORIC TOURING CAR CHALLENGE

 

75 YEARS OF NASCAR

A rare treat on these shores, but a welcome follow-up to the superb NASCAR demonstrations at the recent Goodwood Festival of Speed, a wonderful display of NASCAR Stock cars, ranging from the 1958 Ford Thunderbird, through to contemporary giants, like the 2017 Ford Mustang and 2012 Chevrolet Impala, showcased the brute force and thunderous rumble of the iconic American race cars. In a year when the Hendrick Motorsports Chevrolet Camaro ZL1 wowed crowds at the 24h of Le Mans, running under the Garage 56 rules, and an expanded programme for the Whelan Euro NASCAR Series, European fans have been treated to a special year in chances to witness the powerful V8 powered stock cars, paying tribute to 75 years of the highly successful race series. While the weather curtailed the chances for the NASCAR display on Saturday, those who stuck around til Sunday were treated to a wondrous display, with a soundtrack that epitomized the drama of this thrilling race series.

NON COMPETITIVE TRACK ACTION

Further promoting Silverstone’s 75th birthday and its remarkable Grand Prix heritage, the non-competitive demos offered the stirring sights and sounds of laps by a BRM V16 harking back to the fifties as well as by more modern V8 and V10 propelled F1 cars. Headlines among these were Jacques Villeneuve’s Renault powered Williams FW19 from the late nineties, and current Mercedes-AMG PETRONAS F1 Team driver Esteban Gutiérrez rekindling further memories when putting Lewis Hamilton’s eye-catching Mercedes F1 W04 from 2013 through its paces.

Turning the clocks right back to Silverstone’s origins, the Stuart Graham ‘Scarf and Goggles’ Trophy – presented annually to what is judged to be the most admired racing car on track at the Festival – was presented to Luc Brandts for his Talbot Lago T26, a beautiful machine which actually contested the very first Grand Prix at the circuit back in 1948.

So, how was it? Clearly there was a lot to see. The organisers made the following claim: While glittering gatherings of incredible road and racing cars remained at the core of the amazing three-day event, the evolution of the festival proved to be a huge success attracting a record attendance with a significant uplift of full weekend and Sunday tickets.” Perception does not accord with those claims. This felt like it continued the downward trajectory of 2022. The Foodie area was particularly disappointing, with a vast among of empty space in the two large tents and the redistribution of space sort of masked the reduction in Car Club displays visually, but you review all the Clubs who were not there and the significant drop in display cars on the larger stands and it is hard agree that this the biggest and best yet. It was good, for sure, and there was more than enough to see to keep us entertained for three days but it is starting to feel a bit samey and as if it needs a slightly more significant rethink than just changing the name twice in two years. Let’s see what 2024 brings.